Extron electronics SW2 DVI A Plus Page 34 User Manual Download

Page: 34 / 45

SW DVI Plus Series • Remote Configuration and Control

Click

Connect

. If the connection is successful,

DVI

Plus

Series

appears in green in

the Connected Device section, followed by a green check mark (see

figure 30

on the

next page).

Click the

Browse

button in the New Firmware File (Optional) section.

On the Open window, navigate to the new firmware file, which has an

S19

extension,

and double-click it.

Figure 29.

Open Window for Firmware File Selection

CAUTION:

Valid firmware files must have the file extension

S19

. A file with any

other extension is not a firmware upgrade for these products and could
cause the unit to stop functioning.

NOTES:

•

The original factory-installed firmware is permanently available on the

SW DVI Plus. If the attempted firmware upload fails for any reason, the
switcher reverts to the factory version.

•

When downloaded from the Extron website, by default the firmware is
placed in a folder at:

•

C:\Program

Files\Extron\Firmware\SW

DVI

(Windows XP)

•

C:\Program

Files

(x86)\Extron\Firmware\SW

DVI

Plus

(Windows 7).

Summary of Contents for SW2 DVI A Plus














































Search results

Summary of Contents for SW2 DVI A Plus

Reviews:

Related manuals for SW2 DVI A Plus

Brands by name

Popular brands

Extron electronics SW2 DVI A Plus, User Manual

Search results

Summary of Contents for SW2 DVI A Plus

Reviews:

Related manuals for SW2 DVI A Plus

Brands by name

Popular brands