Extron electronics SW2 DVI A Plus Page 40 User Manual Download

Page: 40 / 45

SW DVI Plus Series • Reference Information

Part Numbers

Included Parts

These items are included with SW DVI Plus Series switcher:

Included Parts

Part Numbers

SW2 DVI Plus
SW2 DVI A Plus
SW4 DVI Plus
SW4 DVI A Plus
SW6 DVI Plus
SW6 DVI A Plus
SW8 DVI Plus
SW8 DVI A Plus

60-964-01
60-964-21
60-965-01
60-965-21
60-966-01
60-966-21
60-967-01
60-967-21

12 VDC, 2 A external power supply

70-055-01

IEC power cord
MBD 149 mounting bracket kit (SW6 and SW8 models only)

70-077-03

3.5 mm 2-pole captive screw power plug

100-454-01

(2) 3.5 mm 5-pole captive screw connectors

100-460-01

SW DVI Plus Series Setup Guide

Extron Software Products DVD
Rubber feet, self-adhesive (4, not attached)

Accessories

These items are optional and may be ordered separately:

Accessories

Part Numbers

IR 102 Remote Control

70-224-10

RSU 129 9.5" deep 1U Universal Rack Shelf Kit

60-190-01

RSB 129 9.5" deep 1U Basic Rack Shelf

60-604-01

RSU 126 6" deep 1U Universal Rack Shelf Kit

60-190-10

RSB 126 6" deep Basic 1U Basic Rack Shelf

60-604-10

RSF 123 3.5" deep 1U Rack Shelf Kit

60-190-20

RSB 123 3.5" deep 1U Basic Rack Shelf

60-604-20

MBU 123 Mini Under-desk kit

70-212-01

MBB 100 Back of the Rack Kit

70-367-01

Cables and Adapters

The following table lists cables and adapters that are available for the SW DVI Plus Series.
For a complete listing of cables, visit the Extron website at

www.extron.com

Cables

Part numbers

DVID SL Single Link DVI-D male-to-male patch cables

26-585-0x

IN9700 Series DVI-D male-to-male extension cables

26-584-0x

DVID SL Pro cables

26-649-xx

Summary of Contents for SW2 DVI A Plus














































Search results

Summary of Contents for SW2 DVI A Plus

Reviews:

Related manuals for SW2 DVI A Plus

Brands by name

Popular brands

Extron electronics SW2 DVI A Plus, User Manual

Search results

Summary of Contents for SW2 DVI A Plus

Reviews:

Related manuals for SW2 DVI A Plus

Brands by name

Popular brands