Exalt EX i GigE Series Installation And Management Manual Download Page 35

Page: 35 / 133

Exalt Installation and Management Guide

EX-i Series FDD Digital Microwave Radios

202675-005

2011-08-30

Install a temporary DC coupling device at the radio antenna port and at the antenna connector.

Connect the RSL test point to the radio antenna port coupler, and the volt meter to the antenna

connector coupler.

•

Verbal relay/walkie-talkie/mobile radio/cell phone
– A person located at the radio front panel can use a short-range communication device or verbal

relay to communicate to the antenna installer and read off RSL voltage measurements

Only use the browser-based GUI for antenna alignment if there are no other means available. If this

method is required, refer to

Exalt Graphical User Interface (GUI)

. The RSL reading can be read on a

PC or any handheld computing device that supports an HTML browser and Ethernet connectivity.

Note:

There is a slight delay in RSL readings in the GUI as the RSL levels change. In this

case, fine alignment can be done in small adjustments allowing a small gap of time so that the

impact of the adjustment on the GUI display catches up to real time.

Summary of Contents for EX i GigE Series






































































































































Search results

Summary of Contents for EX i GigE Series

Reviews:

Related manuals for EX i GigE Series

Brands by name

Popular brands

Exalt EX i GigE Series, Installation And Management Manual

Search results

Summary of Contents for EX i GigE Series

Reviews:

Related manuals for EX i GigE Series

Brands by name

Popular brands