14
Operation
english
Replacing new cutting tips
/ turning sharp edges of
the cutting tips / changing
the complete cutting head.
WARNING: To reduce the risk of injury,
turn unit off and disconnect it from
power source before installing and removing
accessories, before adjusting or when making
repairs.
An accidental start-up can cause injury.
Remove the power plug from the socket. Check
that the motor unit is locked in the upper position.
How to replace or turn the cutting blades
Remove the cutting head cover
(Fig M/1)
by
loosening the screw a bit
(Fig M/2)
with 5 mm
allen key
(
supplied
Fig A/13).
Rotate the cutting
head cover clock wice silghtly so that the base
plate is released. Now you can remove the cover.
Open the cutting blade screw
(Fig M/3)
with TX
15 key. Remove and change the cutting blade or
turn the cutting blade 90 degrees to use a new
sharp cutting edge of the blade (please note that
all the 4 edges of the cutting blade can be used).
Tighten the screws properly. Place the cutting
head cover back and tighten the screw properly.
NOTICE:
All three cutting blades have to
be replaced or turned 90 degrees at the
same time.
How to change the complete cutting head
If you need to achieve a different bevel angle
than the standard 37,5 degrees you have to
change the cutting head. First remove the
cutting head cover as described earlier. Remove
the cutting head with two wrenches (17 mm and
19 mm). The thread is normal right hand thread.
Screw the new cutting head to it’s place and
tighten properly with two wrenches. Assemble
the cutting tips and nally the cutting head cover.
NOTE!
The bevelling angle for the standard
cutting head is 37,5 degrees. Cutting heads for
other beveling angles (eg. 30, 35, 45) please
contact your partner of Exact Tools Oy.
Fig M
Fig N
15
Maintenance, Environment, Guarantee
english
Maintenance and servic-
ing instructions
Remove the power plug from the socket
before servicing or cleaning the beveller.
All maintenance operations to some of
bevellers’s electrical components must be
carried out at an approved service agency.
Cutting head
WARNING:
Check the condition of the
blade tips regulary. Replace blunt, or
otherwise damaged blade tips with a new
set. Using a blunt blade tips can overload the
beveller’s electric motor. They might also crack and
this may cause danger to the operator or property.
Gripper unit
Clean the gripper unit regularly with compressed
air. Lubricate the gripper’s wheel axis
(Fig N/1)
and its joints
(Fig N/2)
. Also clean and lubricate
the gripper’s trapezoidal screw
(Fig N/3)
and the
two worm screws on it
(Fig N/4)
.
Cutting head guard
WARNING:
Check the condition of the
Cutting head guard regulary. It should not
move, wobble or shake at all. If it does, do
not use the machine. Using the machine with
damaged cutting head guard may cause danger
to the user or property.
Motor
Keep the motor’s cooling vents clean.
Plastic parts
Clean the plastic parts with a soft rag. Only use
mild detergents. Do not use solvents or other
strong detergents as they may damage the
plastic parts and paint surfaces.
Power cable
Check the condition of the power cable
regularly. A faulty power cable should
always be replaced at an approved
service agency.
Correct use and regular servicing and cleaning
will ensure the continued operation of the
beveller.
Environment
Separate collection. This product
must not be disposed of with normal
household waste. When your Exact
product is worn out, do not dispose of
it with normal household waste. This
product must be recycled separately.
Separate recycling of used products
and packaging facilitate recycling and recovery
of materials. Reusing of recycled materials helps
prevent pollution of environment. According to
local regulations it is possible to deliver household
appliances to municipal rubbish depositories or to
the dealer when buying a new product.
Guarantee
Warranty terms valid from 01.01.2015
If the Exact product becomes unusable due
to material or manufacturing defects within
Term
at our discretion we will repair the Exact
product or supply an entirely new or factory
ct at no charge.
1.) Copy of a dated purchase receipt is returned
to the Authorized Warranty Repair Center or
has been uploaded to our website at the time
of warranty registration.
2.) The Exact product has not been misused.
3.) No attempt has been made by non-approved
persons to repair the saw.
4.) The Exact product has been used in
accordance with the operating, safety, and
servicing instructions provided in the manual.
5.) The Exact product has been delivered to an
Authorized Warranty Repair Center within the
term of the warranty.
16
17
Replacing new beveling tips /
turning sharp edges of
the beveling tips / changing
the complete cutting head
WARNING:
To reduce the risk of injury, turn
unit off and disconnect it from power source before
installing and removing accessories, before
adjusting or when making repairs.
An accidental
start-up can cause injury.
Remove the power plug from the socket. Check that
the motor unit is locked in the upper position.
How to replace or turn the cutting blades
Remove the cutting head cover (Fig Q/1) by loos-
ening the screw a bit (Fig Q/2) with 5 mm allen
key (supplied Fig A/13). Rotate the cutting head
cover clockwise slightly so that the base plate is
released. Now you can remove the cover.
Open the cutting blade screw (Fig Q/3) with TX 15
key. Remove and change the cutting blade or turn
the cutting blade 90 degrees to use a new sharp
cutting edge of the blade (please note that all the
4 edges of the cutting blade can be used). Tighten
the screws properly. Place the cutting head cover
back and tighten the screw properly.
NOTICE:
All three cutting blades have to be
replaced or turned 90 degrees at the same time.
How to change the complete cutting head
If you need to achieve a different bevel angle than
the standard 37.5 degrees you have to change the
cutting head. First remove the cutting head cover
as described earlier. Remove the cutting head with
two wrenches (17 mm and 19 mm). The thread is
normal right hand thread. Screw the new cutting
head to it’s place and tighten properly with two
wrenches. Assemble the cutting tips and finally
the cutting head cover.
NOTE!
The beveling angle for the standard cutting
head is 30, 37.5 or 45 degrees.
Maintenance and
servicing instructions
Remove the power plug from the socket before
servicing or cleaning the beveller. All maintenance
operations to some of bevellers electrical compo-
nents must be carried out at an approved service
agency.
Cutting head
WARNING:
Check the condition of the
blade tips regularly. Replace blunt, or otherwise
damaged blade tips with a new set. Using a blunt
blade tips can overload the beveller’s electric
motor. They might also crack and this may cause
danger to the operator or property.
Gripper unit
Clean the gripper unit regularly with compressed
air. Lubricate the gripper’s wheel axis (Fig N/1)
and its joints (Fig N/2). Also clean and lubricate
the gripper’s trapezoidal screw (Fig N/3) and the
two worm screws on it (Fig N/4).
Cutting head guard
WARNING:
Check the condition of the Cutting
head guard regularly. It should not move, wobble
or shake at all. If it does, do not use the machine.
Using the machine with damaged cutting head
guard may cause danger to the user or property.
Motor
Keep the motor’s cooling vents clean.
Plastic parts
Clean the plastic parts with a soft rag. Only use
mild detergents. Do not use solvents or other
strong detergents as they may damage the plastic
parts and paint surfaces.
Power cable
Check the condition of the power cable
regularly. A faulty power cable should always be
replaced at an approved service agency.
Correct use and regular servicing and cleaning will
ensure the continued operation of the beveller.
Environment
Separate collection. This product must not
be disposed of with normal household waste.
When your Exact product is worn out, do not
dispose of it with normal household waste. This
product must be recycled separately. Separate
recycling of used products and packaging facil-
itate recycling and recovery of materials. Reus-
ing of recycled materials helps prevent pollution
of environment. According to local regulations it
is possible to deliver household appliances to
municipal rubbish depositories or to the dealer
when buying a new product.
Guarantee
Warranty terms valid from 01.01.2015
If the Exact product becomes unusable due to
material or manufacturing defects within the
the warranty term
o
ur discretion we will repair the Exact product o r
supply an entirely new or factory reconditioned
Warranty term
The Exact Tools warranty term is 12 months
from date of purchase.
T
The warranty is valid if
1.) Copy of a dated purchase receipt is returned
to the Authorized Warranty Repair Center or
has been uploaded to our website at the
time of warranty registration.
2.) The Exact product has not been misused.
3.) No attempt has been made by non-approved
persons to repair the beveller.
4.) The Exact product has been used in
accordance with the operating, safety,
and servicing instructions provided in the
manual.
5.) The Exact product has been delivered to
an Authorized Warranty Repair Center within
the term of the warranty.
Fig Q
Fig R
