10
Safety
english
Additional speci c safety
rules
The pipe bevel machine must never be used
in the following cases, if:
• There is water or another liquid, explosive
gases or poisonous chemicals inside the pipe
to be bevelled.
• The power switch is faulty.
• The power cable is faulty.
• One blade tip is broken.
• One blade tip is blunt or in poor condition.
• The plastic components are cracked or have
parts missing.
• The gripper unit is not properly tightened
around the pipe or if it is warped.
• The blade cover has been damaged or
removed from the machine.
• The locking mechanisms do not work
properly (UNLOCK-button).
• The pipe bevel machine has become wet.
When using the pipe bevel machine, the
following factors must always be taken into
consideration:
• Support tubes to minimise the risk of blade
jamming.
• Ensure that the pipe to be bevelled is empty.
• Ensure that the blade tips are correctly
installed.
• Ensure that the dimensions and the thickness
of the blade tips are suitable for the blade
holder and that the blade tips are suitable for
the rpm-range of the machine.
• Never use sideways force to stop the blade
holder, always allow the blade holder to stop
freely.
• Check the attachments of the blade cover.
• Never use excessive force when using the
pipe beveller.
• Never use the pipe beveller to lift the pipe
while it is still attached to the pipe.
• Avoid overloading the electric motor.
• Always follow the safety and operating
instructions and current regulations.
Functional Description
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, re and/or serious
injury.
Intended Use
PipeBevel 220E/360E:
The PipeBevel 220E/360E machine is
intended for use as a pipe tter’s tool
at the installation site. The PipeBevel 220E/360E
machine can only be used to bevel round pipes,
with a diameter of 25-220 mm model 220E and
110 - 360 mm model 360E and a maximum wall
thickness of 10 mm. The PipeBevel 220E/360E
machine can be used to bevel steel, stainless
steel and aluminium pipes. The PipeBevel
220E/360E machine is intended for short,
intermittent use. The machine may be loaded
for 2,5 minutes during a 10-minute period
(S3 25 %). The PipeBevel 220E/360E machine
is not intended for use in industrial production.
Use pipe supports to support pipe.
Figure A
1. UNLOCK button
2. Power switch
3. Power switch locking lever
4. Bevel level control bar screw
5. Rotation direction arrow
6. Blade cover
7. Reference bearing
8. Braking wheels
9. Guidance wheels
10. Operating handle
11. Motor unit adjustement screw
12. Motor unit
13. Blade cover key
14. Rating plate
15. Rpm regulator
16. Gripper unit
17. Gripper adjustment handle
11
Operation
english
Exact PipeBevel
220E/360E pipe bevelling
system operating
instructions
Before operating the tool
Ensure that the motor unit is in the upright
position. The yellow mark of the UNLOCK button
should be visible.
Check that the blade holder and the blade
tips are correctly tted, in good condition and
suitable for the material to be beveled.
Ensure the pipe bevel machine wheels rotate.
Ensure the support wheels rotate.
Check the operation of the motor unit adjustment
screw.
Ensure that the bevel level control bar is in the
upper position (
Fig C)
.
Ensure that the pipe is empty.
Fig B
Connection to the mains power supply
Ensure that the mains voltage is the same as
indicated on the rating plate
(Figure A/14).
Connect the pipe saw to the power outlet only
after having checked this.
Setting the pipe on supports
Use the system supports when bevelling pipes.
This will ensure safe working and optimum
result. Work on at surface. Place the pipe
on the two supports (
Fig B)
that are supplied
with the system. Check that all support wheels
contact the pipe (adjust if required e.g. with
pieces of lumber).
Fig C
Functional Description
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
Intended Use
PipeBevel 220E/360E:
The Exact PipeBevel 220E/360E Pipe
Beveling machine is intended for use as pipe
fitter’s or welder’s tool at installation site.
The PipeBevel 220E/360E can only be used
to bevel round pipes, with diameter of 220E:
1”– 8.6” (25 mm –220 mm) or 360E: 4.3”–14”
(110 mm – 360 mm) and maximum bevel
depth in 0.4” (10 mm) with steel and other
ferrous and non-ferrous materials. The Pipe-
Bevel 220E/360E pipe beveller can be used to
bevel normal weldable pipe materials, such as
steel, aluminium and stainless steel. PipeBevel
220E/360E pipe beveling machine is intended
for short and intermitten use. The Machine may
be loaded for 2.5 minutes during a 10-minute
period (S3 25 %). PipeBevel 220E/360E pipe
beveling machine is not intended for rapid use,
such as industrial prodcution. Use Pipe Holders
to support pipe.
10
Safety
english
Additional specic safety
rules
The pipe bevel machine must never be used
in the following cases, if:
• There is water or another liquid, explosive
gases or poisonous chemicals inside the pipe
to be bevelled.
• The power switch is faulty.
• The power cable is faulty.
• One blade tip is broken.
• One blade tip is blunt or in poor condition.
• The plastic components are cracked or have
parts missing.
• The gripper unit is not properly tightened
around the pipe or if it is warped.
• The blade cover has been damaged or
removed from the machine.
• The locking mechanisms do not work
properly (UNLOCK-button).
• The pipe bevel machine has become wet.
When using the pipe bevel machine, the
following factors must always be taken into
consideration:
• Support tubes to minimise the risk of blade
jamming.
• Ensure that the pipe to be bevelled is empty.
• Ensure that the blade tips are correctly
installed.
• Ensure that the dimensions and the thickness
of the blade tips are suitable for the blade
holder and that the blade tips are suitable for
the rpm-range of the machine.
• Never use sideways force to stop the blade
holder, always allow the blade holder to stop
freely.
• Check the attachments of the blade cover.
• Never use excessive force when using the
pipe beveller.
• Never use the pipe beveller to lift the pipe
while it is still attached to the pipe.
• Avoid overloading the electric motor.
• Always follow the safety and operating
instructions and current regulations.
Functional Description
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, re and/or serious
injury.
Intended Use
PipeBevel 220E/360E:
The PipeBevel 220E/360E machine is
intended for use as a pipe tter’s tool
at the installation site. The PipeBevel 220E/360E
machine can only be used to bevel round pipes,
with a diameter of 25-220 mm model 220E and
110 - 360 mm model 360E and a maximum wall
thickness of 10 mm. The PipeBevel 220E/360E
machine can be used to bevel steel, stainless
steel and aluminium pipes. The PipeBevel
220E/360E machine is intended for short,
intermittent use. The machine may be loaded
for 2,5 minutes during a 10-minute period
(S3 25 %). The PipeBevel 220E/360E machine
is not intended for use in industrial production.
Use pipe supports to support pipe.
Figure A
1. UNLOCK button
2. Power switch
3. Power switch locking lever
4. Bevel level control bar screw
5. Rotation direction arrow
6. Blade cover
7. Reference bearing
8. Braking wheels
9. Guidance wheels
10. Operating handle
11. Motor unit adjustement screw
12. Motor unit
13. Blade cover key
14. Rating plate
15. Rpm regulator
16. Gripper unit
17. Gripper adjustment handle
12
13
Exact PipeBevel 220E/360E
pipe beveling system
operating instructions
Before operating the tool
Ensure that the motor unit is in the upright
position. The yellow mark of the UNLOCK button
should be visible.
Check that the blade holder and the blade tips
are correctly fitted, in good condition and suitable
for the material to be beveled.
Ensure the pipe bevel machines gripping unit’s
wheels rotate.
Ensure the support wheels rotate.
Check the operation of the motor unit adjustment
screw.
Ensure that the bevel level control bar is in the
upper position
(Fig C)
.
Ensure that the pipe is empty.
Connection to the mains power supply
Ensure that the mains voltage is the same as
indicated on the rating plate
(Figure A/14)
.
Connect the pipe beveling machine to the power
outlet only after having checked this.
Setting the pipe on supports
Use the system supports when beveling pipes.
This will ensure safe working and optimum result.
Work on flat surface. Place the pipe on the
two supports
(Fig B)
that are supplied with the
system. Check that all support wheels contact
the pipe (adjust if required e.g. with pieces of
lumber).
