EVS Synapse U4T100 Installation & Configuration Manual Download Page 34

Page: 34 / 68

INSTALLATION AND CONFIGURATION MANUAL

U4T100-U4T140

#Dialogue_Lev

Dialogue level sets the average loudness of a dialogue in a
presentation. The range is from –31dB to –1dB.
The default setting is –27dB

#Ch_mod

This setting sets the channel mode of the dolby signal. Default is
1/0(C). Possible settings are:

▪

1/0(C)

▪

2/0(LR)

▪

3/0(LCR)

▪

2/1(LRS)

▪

3/1(LCRS)

▪

2/2(LRSlSr)

▪

3/2(LCRSlSr)

#Line

Line sets the Dynamic range metadata of presets (Default is

None

▪

None

, no dynamic range compression is applied unless

downmixing could cause overload, in which case protection
dynamic range is automatically applied.

▪

Film stnd

, applies more compression to a subjectively loud

film that requires dynamic range restriction.

▪

Film Light

, applies light compression to a subjectively

quiet film that does not require dynamic range restriction.

▪

Music Stnd

, applies more compression to music that is not

compressed and requires dynamic range restriction.

▪

Music light

, applies light compression to music that is

already compressed and does not require excessive dynamic
range restriction.

▪

Speech

, Appropriate for programs with predominantly

dialogue.

#RfMode

RfMode

has the same options as Line, but each option is 11 dB more

sensitive to avoid overloading the RF input of a television. Possible
are:

None

Film stnd

Film light

Music stnd

Music

light

and

speech

. Default is

None

Summary of Contents for Synapse U4T100





































































Search results

Summary of Contents for Synapse U4T100

Reviews:

Related manuals for Synapse U4T100

Brands by name

Popular brands

EVS Synapse U4T100, Installation & Configuration Manual

Search results

Summary of Contents for Synapse U4T100

Reviews:

Related manuals for Synapse U4T100

Brands by name

Popular brands