EVS Synapse U4T100 Installation & Configuration Manual Download Page 30

Page: 30 / 68

INSTALLATION AND CONFIGURATION MANUAL

U4T100-U4T140

Main_DRC_DD

With this setting you decide whether you want to apply the dynamic
range (

None (Dialnorm)

RF mode

Line mode

) to the

output signal of the decoder when the input is Dolby Digital.

Main_DRC_E

With this setting you decide whether you want to apply the dynamic
range (

None (Dialnorm)

RF mode

Line mode

) to the

output signal of the decoder when the input is Dolby E.

Main_DRC_PCM

With this setting you decide whether you want to apply the dynamic
range (

None (Dialnorm)

RF mode

Line mode

) to the

output signal of the decoder when the input is PCM.

Aux_DRC_DD

With this setting you decide whether you want to apply the dynamic
range (

RF mode

Line mode

) to the monitoring signal of the

decoder when the input is Dolby Digital.

Aux_DRC_E

With this setting you decide whether you want to apply the dynamic
range (

RF mode

Line mode

) to the monitoring signal of the

decoder when the input is Dolby E.

Aux-DRC_PCM

With this setting you decide whether you want to apply the dynamic
range (

None (Dialnorm)

RF mode

Line mode

) to the

monitoring signal of the decoder when the input is PCM.

Summary of Contents for Synapse U4T100





































































Search results

Summary of Contents for Synapse U4T100

Reviews:

Related manuals for Synapse U4T100

Brands by name

Popular brands

EVS Synapse U4T100, Installation & Configuration Manual

Search results

Summary of Contents for Synapse U4T100

Reviews:

Related manuals for Synapse U4T100

Brands by name

Popular brands