2
Operating Instructions
Important
Please read these operating and safety instructions carefully and completely.
For your own safety, before using this equipment check that the voltage is
correct and that all handles and parts are firmly secured. If you are uncertain
about any aspect of using this equipment contact your distributor.
Please Keep These Instructions
Model Bear 300 (ME7500) Specifications
Motor (4 Speed) (230v or 115v 50/60 Hz) (Watts):
1800
Maximum Cutter Diameter:
3” 75mm
Maximum Cutting Depth:
2”
50mm
Maximum Drill Diameter (Morse Taper No. 3):
1-1/4” 32mm
Maximum Tap Diameter:
15/16” 24mm
RPM No Load (Speed 1) (min-1):
210
RPM No Load (Speed 2) (min-1):
270
RPM No Load (Speed 3) (min-1):
410
RPM No Load (Speed 4) (min-1):
530
Recommended Maximum Duty Cycle (Minutes):
30
Sound Pressure Level (Under Load) (dB(A)):
104
Weight:
54lb 24.6kg
Max Dimensions (Rack Fully Raised): 24-3/8” x 11-7/16” x 13” 618 x 290 x 330
Min Dimensions (Rack Fully Lowered): 20-11/16” x 9-7/16” x 12-1/2” 526 x240 x 320
Magnet Dimensions:
4” x 2-9/16” x 7-7/8” 100 x 65 x 199
Magnetic Adhesion:
4950lb 2250kg f
Cutter Retainer Internal Diameter:
3/4” 19mm Weldon Shank
Standard Equipment Supplied With Unit: 1 Coolant Tank, 1 Coolant Pipe, 1
Guard, 1 Hex key 2.5mm, 1 Wrench 8mm, 3 Handles, 2 Butterfly Screws, 2
Spring Washers, 1 Chain, 1 Drift, Carry Case.
Ear and eye protection MUST be worn while operating this equipment.
Do NOT touch the cutter while it is in motion. Always follow the Personal
Protection Equipment (PPE) recommendations while operating this tool.
This machine is designed specifically for drilling holes in mild steel using the
appropriate cutters and accessories. It should NOT be modified and / or used
for any application other than for which it was intended, including powering other
equipment.
Ensure that the total work area can be viewed from the operating position. Use
barriers to keep people away. Do not operate the tool in explosive environments
– power tools create sparks that may ignite flammable materials or gases. Do
not operate the tool in damp or wet conditions or areas, as electric shocks may
result. Always use both hands to operate the tool. Always ensure that the material
you are working on is securely clamped.
•
This tool is equipped with an approved cord and plug for its intended
Country of use. The green and yellow conductor in the cord is the grounding
wire,
never
connect this to a live terminal.
•
Remove plug from power supply before replacement of the cutter, making
adjustments or other maintenance work.
•
We recommend the use of genuine Evolution supplied cutters.
•
Inspect the machine and cutter before each use and do not use
deformed, cracked, worn or otherwise damaged cutters.
•
Ensure the cutter is correctly mounted and do not stop by hand.
•
Do not use cutters that do not comply with the characteristics specified in
these instructions.
•
Ensure that the gibs (dovetail slides) are correctly adjusted before
each use. This is essential for proper and safe operation of the
machine.
•
Always keep the power cord away from moving parts of the tool.
•
When you put the tool away, switch off the motor and ensure that all moving
parts have come to a complete standstill.
•
Never use the tool without the original protection guard system
.
Magnetic Drill Safety
The drill’s magnetic adhesion depends on the thickness of the work piece. 1/2”
(12mm) is the optimum thickness for safe operation. Keep the magnet clean of
metal chips and other dirt and debris. These will seriously reduce the magnetic
