background image

There are only three O-rings and one urethane Regulator seat in the EVIL

®

Detonator.

If a leak is detected, the fault lies with one of the three O-rings. If the regulator fails to
hold a consistent delivery pressure, then the problem is with the Regulator Seat (4).

The EVIL

®

Pimp Kit

is designed to be very low maintenance.

The EVIL

®

Detonator

must be well maintained as most issues will start with neglect of the Detonator

inline

regulator. Run a couple of drops of 100% synthetic oil through the Detonator after every
10 cases of paint. The easiest way to oil the internals of Detonator is to drop three drops
in the inlet port or the ASA and air the marker up.

Complete maintenance of the Detonator should never have to be performed unless dirt 
is introduced into the system or a leak is detected.

Improper disassembly will void

warranty.

To completely disassemble the Detonator the Snap Ring (10) and both the

Locking Screw (11) and the Retaining Screw (14) must be removed. The Seal Retainer (6)
and Inner Tube (3) are Blue Loc Tited together and if that Loc Tite is broken it will void the
warranty.

Oil the top Piston O-ring (15).
Oil the bottom 1/3 of the Piston Shaft (9); this should oil Poppet O-ring (13).
Do not lube the tip.

If you tighten the Retaining Screw during reassembly the Detonator will not turn properly.

Loc Tite the seal retainer and inner tube back together with a small amount of Blue Loc Tite.
Make sure they screw all the way together or it will leak.

EVIL

®

Detonator

Service Procedures

For Experts Only - Do Not Attempt to disassemble EVIL

®

Detonator

without reading 

complete instructions.

Normal Maintenance

Note: The PIMP KIT’s valve was designed for more cycles of trouble free performance than 
most players can afford to play. There should be no reason to remove the valve body from marker
main body.

The EVIL

®

Pimp Kit

is easy to strip for cleaning and basic maintenance. Regular 

cleaning and maintenance is highly recommended, including checks of regulator 
components. Keep screws tightened. Replace worn components with factory parts; all
leaks must be repaired promptly. Solenoid or electronic repairs are best performed by 
the factory or an authorized factory repair facility; contact PMI for information regarding
authorized repair facilities: 1.800.579.1633.

DO NOT ATTEMPT TO PERFORM MAINTENANCE PROCEDURES UNLESS 
QUALIFIED TO DO SO. DO NOT DISASSEMBLE MARKER UNTIL IT IS COMPLETELY
DRAINED OF COMPRESSED GAS OR AIR AND ALL PAINTBALLS HAVE BEEN
REMOVED. FILLING OF COMPRESSED GAS OR AIR CYLINDERS MUST BE DONE 
BY QUALIFIED PERSONS. DISASSEMBLY OF REGULATOR MAY VOID WARRANTY.

CONTACT PMI, INC., FOR REPAIR ASSISTANCE AND INFORMATION REGARDING
AUTHORIZED REPAIR FACILITIES. PHONE 800.579.1633; WWW.BUYPMI.COM

01 Detonator End Cap

57201

02 Detonator Adjusting Ring

57202

03 Inner Tube

57203

04 Regulator Seat

57204

05 Thrust Element

57205

06 Seal Retainer

57206

07 Detonator Main Body

57207

08 Piston Spring

57208

09 Piston

57209

10 Snap Ring

57210

11 Locking Screw 10/32 Oval Point

57211

12 O-Ring 011/70 Buna

57212

13 O-Ring 008/90 Urethane (Poppet O-ring)

40923

14 Retaining Screw 8/32 Dog Point

57213

15 O-Ring 012/90 Urethane

40919

16 Screen Filter

71667

17 10/32 Black Lower Locking Screw

41318

EVIL

®

Pimp Kit

Detonator Diagram

EVIL

®

Pimp Kit

Detonator Maintenance

19

18

Disassembly will void warranty

Summary of Contents for Pimp Kit


















Reviews: