evertz 9780MUX-IPGE-ASI User Manual Download Page 43 | Manualshive

Page: 43 / 64

background image

9780MUX-IPGE-ASI

Compact ASI/IP Re/De-Multiplexer

Revision 1.0

Page - 33

Figure

4-32 : VistaLINK

®

PRO - Edit PID Descriptors

Edit PID Descriptors:

Add, edit or remove Elementary Stream descriptors to a maximum of 5 per PID.

4.4.3. Active Output\Output Tab

The user can configure the outputs through Active Output too but it is not allowed to configure or modify
all the specifications on the Active mode.

Push “Load from Preset” button in order to activate new configuration as shown in Figure

«
...
41
42
43
44
45
...
»

Summary of Contents for 9780MUX-IPGE-ASI

































































Reviews:

No comments

Related manuals for 9780MUX-IPGE-ASI

Brand: Tenma Pages: 20

Brand: Campbell Pages: 24

Brand: MARTINDALE Pages: 2

Brand: Owon Pages: 45

pH/CON 510 series

Brand: Oakton Pages: 47

Brand: Mastech Pages: 31

Brand: RAPITEST Pages: 25

Brand: MAC TOOLS Pages: 54

Brand: APPA Pages: 57

Brand: koban Pages: 36

Brand: Novus Pages: 88

Brand: LIMIT Pages: 11

Brand: Fluke Pages: 16

Brand: Fluke Pages: 16

Brand: Fluke Pages: 20

Brand: Fluke Pages: 50

Brand: Victor Pages: 22

Brand: Steren Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands