evertz 9780MUX-IPGE-ASI User Manual Download Page 21 | Manualshive

Page: 21 / 64

background image

9780MUX-IPGE-ASI

Compact ASI/IP Re/De-Multiplexer

Revision 1.0

Page - 11

4.1.2. Ethernet Ports Control Tab

Figure

4-3 : VistaLINK

®

PRO Hardware Configuration – Ethernet Ports Tab

Default Gateway:

The default value is none but user can specific a specific gateway IP.

This tab allows Mapping on the rear of the MUXIP to VLPro data port configuration.

DATA 3, DATA 4

and

Control Port 2 are not used

.

Control Port 1 Control Port 2

Data Port 1

Data Port 2

Data Port 3

Data Port 4

Control

NA

DATA1

DATA2

NA

NA

Table

4-1 : VistaLINK

®

PRO Mapping to Rear to 9780MUX-IPGE

IP address:

Self IP address of the port.

Netmask:

The Netmask address which is 255.255.255.0 by default.

«
...
19
20
21
22
23
...
»

Summary of Contents for 9780MUX-IPGE-ASI

































































Reviews:

No comments

Related manuals for 9780MUX-IPGE-ASI

Brand: Malmbergs Pages: 20

Brand: East Tester Pages: 51

Brand: Draper Pages: 28

Brand: Moog Pages: 6

Brand: Chekman Pages: 2

Brand: C-LOGIC Pages: 4

Brand: Amprobe Pages: 73

Brand: ADInstruments Pages: 45

Brand: Beta Pages: 196

Brand: Mastech Pages: 14

Brand: LIMIT Pages: 149

Brand: V&A Pages: 27

Brand: Tenmars Pages: 40

Brand: YATO Pages: 36

PAN Pocketmeter

Brand: PANCONTROL Pages: 186

Brand: IDEAL Pages: 90

Brand: TC Communications Pages: 39

Brand: Dawson Tools Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands