evertz 9780MUX-IPGE-ASI User Manual Download Page 51 | Manualshive

Page: 51 / 64

background image

9780MUX-IPGE-ASI

Compact ASI/IP Re/De-Multiplexer

Revision 1.0

Page - 41

4.4.3.7. Active Output\Fault Tab

Figure

4-39 : VistaLINK

®

PRO – Mux Output - Fault Tab

Output:

This trap will be triggered when Output is not present.

Meta Data:

This trap will be triggered when Meta data is not present.

4.4.4. Adding Input on the Output section

This section allows the user to configure or modify the input settings. By clicking the “Configuration”
button, the user will have access to the input window configuration.

Note:

Make sure that input is enabled and input mode is IP or ASI and probe mode is ATSC.

«
...
49
50
51
52
53
...
»

Summary of Contents for 9780MUX-IPGE-ASI

































































Reviews:

No comments

Related manuals for 9780MUX-IPGE-ASI

Brand: Paradyne Pages: 19

Brand: Velleman Pages: 4

Brand: CEM Pages: 2

Brand: CEM Pages: 22

UNITEST Hexagon 55

Brand: Beha-Amprobe Pages: 95

Brand: Snap-On Pages: 15

Brand: UNI-T Pages: 14

Brand: Brymen Pages: 20

Brand: Brymen Pages: 16

Brand: Brymen Pages: 16

Brand: Brymen Pages: 24

Brand: Brymen Pages: 32

Brand: UNI-T Pages: 5

Brand: Raisecom Pages: 24

Brand: Mastech Pages: 11

Brand: YATO Pages: 52

Brand: MARTINDALE Pages: 6

Brand: MARTINDALE Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands