evertz 9780MUX-IPGE-ASI User Manual Download Page 16 | Manualshive

Page: 16 / 64

background image

9780MUX-IPGE-ASI

Compact ASI/IP Re/De-Multiplexer

Page - 6

Revision 1.0

d. Type 2 to set IP address
e. Type 4 to set Gateway

f. Type x to exit Control port menu

g. Type x to exit Network Configuration menu.

h. Type x to exit and save configuration.

i. The same steps can be done for Data 1(Data Main) and Data 2(Data Redundant) interfaces.

j. All other Data ports must be configured through VLPro. Data 3 and Data 4 are not defined in

9780MUX-IPGE as if the box only supports

Figure

2-3 : Configure IP Interfaces to the MUXIP

«
...
14
15
16
17
18
...
»

Summary of Contents for 9780MUX-IPGE-ASI

































































Reviews:

No comments

Related manuals for 9780MUX-IPGE-ASI

Brand: Keithley Pages: 366

Brand: Wavetek Pages: 22

Brand: Keithley Pages: 96

Brand: Keithley Pages: 28

SI Analytics HandyLab 680

Brand: Xylem Pages: 50

Brand: UNI-T Pages: 4

Brand: UNI-T Pages: 38

Brand: UNI-T Pages: 20

Brand: EEVBlog Pages: 76

Brand: ELECTRO SYSTEMS Pages: 4

Brand: Agilent Technologies Pages: 8

Brand: IEK Pages: 28

Brand: Elma Pages: 52

Brand: Mastech Pages: 18

Brand: Mastech Pages: 2

Brand: UNI-T Pages: 30

Brand: Maxwell Pages: 12

Brand: IDEAL Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands