evertz 7847FSEDA Series User Manual Download Page 80

Page: 80 / 86

7847FSEDA Series

Frame Synchronizer and Distribution Amplifier

Page - 70

Revision 0.1

7.1.

VISTALINK® PRO PRODUCT JAR UPGRADE

Open VISTALINK

PRO Server and navigate to

Help > Apply Update > Product.

When the window

opens you want to select the latest .jar file for the 7847FSEDA, from its saved location on the computer
and select

Open

Figure 7-1: VistaLINK

PRO JAR Upgrade - Upgrade Window

At this point the VistaLINK

PRO Server will send a message asking to Restart, select

Yes

. This will

apply the JAR update to the 7847FSEDA. Restart VISTALINK

PRO Server followed by VISTALINK

PRO Client.

When VISTALINK

PRO Client has re-opened, verify that the 7847FSEDA is running the correct

version, to check this simply right click on the cards address in VistaLINK

PRO Client and select

Version Information

Summary of Contents for 7847FSEDA Series























































































Search results

Summary of Contents for 7847FSEDA Series

Reviews:

Brands by name

Popular brands

evertz 7847FSEDA Series, User Manual

Search results

Summary of Contents for 7847FSEDA Series

Reviews:

Brands by name

Popular brands