manualshive.com logo in svg

evertz 7847FSEDA Series, User Manual

Share
Download
evertz 7847FSEDA Series User Manual Download Page 72

7847FSEDA Series 

Frame Synchronizer and Distribution Amplifier

 

 

Page - 62

 

Revision 0.1

 

 

 

Figure 5-24: Video Path Configuration - ANC PassThru Tab 

 

Direct ANC PassThru 

Direct ANC PassThru: 

This control allows the user to 

Enable 

or 

Disable 

Direct ANC data passthru 

for ANC data that is not processed through the module to pass through without getting striped on the 
output video signal.   
 

 
Mapped ANC PassThru 

ANC Index Select: 

This control allows the user to select which of the 10 

Mapped ANC PassThru

 

rules to configure.  Each 

Mapped ANC PassThru

 rule contains its own unique set of control values. 

 

ANC PassThru 

Mapped ANC Packet PassThru: 

This control allows the user to enable / disable the 

Mapped ANC 

PassThru

 rule as defined by its controls. When set to 

Enable 

the 

Mapped ANC PassThru

 rule will 

be applied to route any ANC packets on the input with matching DID and SDID (

if relevant

) to the 

ANC of the output video. When set to Disable, the rule will not be applied, and all ANC packets on the 
input with matching DID and SDID (

if relevant

) will not be included in the ANC of the output video. 

 

 

NOTE: 

Direct AND PassThru is only functional when input and output video standards are 

identical.

 

Summary of Contents for 7847FSEDA Series























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands