manualshive.com logo in svg

evertz 7847FSEDA Series, User Manual

Share
Download
evertz 7847FSEDA Series User Manual Download Page 55

7847FSEDA Series  

Frame Synchronizer and Distribution Amplifier 

 

 

Revision 0.1

 

Page - 45

 

5.2.13. Upmix Mixer [+UMX2] 

The Upmix Mixer tab contains controls for audio routing, audio gain, and audio inversion for the Upmix 
audio processing module input channels.  Each Upmix input audio channel mixer consists of two 
independently selectable sources (X & Y) with each source having its own gain and inversion controls.  
The selectable sources for the Upmix audio mixers may vary based on the audio options enabled on 
the module. Table 5-5 lists all the selectable sources for the Upmix audio mixers, and which sources 
are enabled by product options. Figure  5-20  illustrates the layout of these controls in the VistaLINK® 
PRO configuration view. 
 

 
 

Product Option 

Mixer Sources 

All Products 

Mute 
DMX channels 1-16 
Mono mix DMX channels (8 pairs – 1&2, 3&4, etc.) 
Down mix L, R 
Down mix mono 

IntelliGain

®

 [+IG2] 

IntelliGain 1 channels 1-8 
IntelliGain 2 channels 1-8 

Table 5-5: Upmix Mixer - Selectable Audio Sources 

 

 

NOTE: 

The Upmix Mixer tab is only visible when [+UMX2] is included in the module’s 

product string.

 

Summary of Contents for 7847FSEDA Series























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands