manualshive.com logo in svg

evertz 7780ASIB2-DS3/E3, Manual

Share
Download
evertz 7780ASIB2-DS3/E3 Manual Download Page 2

7700 MultiFrame Manual 

7780ASIB2-DS3/E3 2 Channel ASI + Ethernet DS3/E3 Transceiver 

 Revision 

2.0

 

5.5.1.

 

Control ......................................................................................................................22

 

5.5.2.

 

Monitor .....................................................................................................................22

 

5.6.

 

ASI OUTPUT 1 ....................................................................................................................22

 

5.6.1.

 

Control ......................................................................................................................22

 

5.6.2.

 

Monitor .....................................................................................................................22

 

5.7.

 

ASI FAULTS ........................................................................................................................23

 

5.8.

 

FAULTS ...............................................................................................................................24

 

6.

 

JUMPERS........................................................................................................................................25

 

6.1.

 

SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED  BY 
THE GLOBAL FRAME STATUS.........................................................................................25

 

6.2.

 

CONFIGURING THE MODULE FOR FIRMWARE UPGRADES ........................................26

 

6.2.1.

 

Using the Upgrade Jumper ......................................................................................26

 

6.2.2.

 

Upgrade Serial Port Command ................................................................................26

 

7.

 

VISTALINK

®

 REMOTE MONITORING/CONTROL .........................................................................27

 

7.1.

 

WHAT IS VISTALINK

®

? ......................................................................................................27

 

7.2.

 

CONFIGURING THE IP ADDRESS (IF THE ONBOARD MINI AGENT 
IS USED)..............................................................................................................................28

 

7.3.

 

VISTALINK

®

 MONITORED PARAMETERS........................................................................30

 

7.4.

 

VISTALINK

®

 CONTROLLED PARAMETERS.....................................................................31

 

7.5.

 

VISTALINK

®

 TRAPS ...........................................................................................................31

 

 

 

Figures 

Figure 1-1: 7780ASIB2-DS3/E3 Block Diagram ................................................................................................... 2

 

Figure 2-1: 7780ASIB2-DS3/E3 Rear Panel ......................................................................................................... 3

 

Figure 4-1: Location of Status Indicators and Controls......................................................................................... 7

 

Figure 4-2: Card Edge Menu............................................................................................................................... 10

 

Figure 5-1: General Tab ...................................................................................................................................... 18

 

Figure 5-2: Errored Second Control Tab............................................................................................................. 19

 

Figure 5-3: Errored Second Status Tab .............................................................................................................. 20

 

Figure 5-4: ASI Bandwidth Monitor Tab .............................................................................................................. 21

 

Figure 5-5: ASI Input 1 Tab ................................................................................................................................. 21

 

Figure 5-6: ASI Output 1 Tab .............................................................................................................................. 22

 

Figure 5-7: ASI Faults Tab .................................................................................................................................. 23

 

Figure 5-8: Faults Tab ......................................................................................................................................... 24

 

Figure 6-1: Location of Status Indicators and Jumpers ...................................................................................... 25

 

 

 

Tables 

Table 6-1: 

Vista

LINK

®

 Monitored Parameters..................................................................................................... 30

 

Table 6-2: 

Vista

LINK

®

 Controlled Parameters .................................................................................................... 31

 

Table 6-3: 

Vista

LINK

®

 Traps ............................................................................................................................... 31

 

 

 

Summary of Contents for 7780ASIB2-DS3/E3





































Reviews:

No comments

Brands by name

Popular brands

Load more brands