manualshive.com logo in svg

evertz 7780ASIB2-DS3/E3, Manual

Share
Download
evertz 7780ASIB2-DS3/E3 Manual Download Page 34

7700 MultiFrame Manual 

7780ASIB2-DS3/E3 2 Channel ASI + Ethernet DS3/E3 Transceiver 

Page - 30

 Revision 

2.0 

7.3. 

VISTALINK

®

 MONITORED PARAMETERS 

The following parameters can be remotely monitored through the 

Vista

LINK

®

 interface. 

 

Parameter Description 

Card Type 

Identifies the type of card. 

TDMD Status 

Indicates TDMD Status. 

Firmware Version 

Indicates current Firmware Version. 

Ethernet Monitor 

Indicates Ethernet Link Status, Speed, and Bandwidth. 

Current Interval Performance 
Counters 

Indicates the current 15 minute and current 24 hour performance 
counters, Signal Loss, Out of Frame, Alarm Indication Signal, 
Remote Alarm Indication, DS3 Idle Signal, and Severely Errored 
Frame. 

Last Interval Performance 
Counters 

Indicates the last 15 minute and last 24 hour performance 
counters, Signal Loss, Out of Frame, Alarm Indication Signal, 
Remote Alarm Indication, DS3 Idle Signal, and Severely Errored 
Frame. 

Interval Elapsed Time 

Indicates the current timer on 15 minute and 24 hour counter. 

Input Used Data Bitrate 

Indicates the sum of the two input channel bandwidths. 

Output Used Data Bitrate 

Indicates the sum of the two output channel bandwidths. 

Input ASI Status Information 

Indicates the status parameters of Input ASI streams, Input 
Status, TS Total Bitrate, TS Null Bitrate, TS Useful Bitrate, 
Number of PIDs, and Continuity Error Count.   

Output ASI Status Information 

Indicates the status parameters of Output ASI streams, Output 
Status, TS Total Bitrate, TS Null Bitrate, TS Useful Bitrate, 
Number of PIDs, and Continuity Error Count.   

Table 7-1: VistaLINK

®

 Monitored Parameters 

Summary of Contents for 7780ASIB2-DS3/E3





































Reviews:

No comments

Brands by name

Popular brands

Load more brands