evertz 7780ASIB2-DS3/E3 Manual Download Page 20

Page: 20 / 36

7700 MultiFrame Manual

7780ASIB2-DS3/E3 2 Channel ASI + Ethernet DS3/E3 Transceiver

Page - 16

Revision

2.0

4.2.2.8.

Displaying the Ethernet Bandwidth

This menu selection displays the current

Ethernet Bandwidth

allocated. To display the

Ethernet

Bandwidth

from the

STAT

menu, use the toggle switch/pushbutton to select the

ETH

menu and then

choose

BW.

STAT

ETH

0-25

The following indications are possible:

0-25

Indicates the total bandwidth allocated for Ethernet transport

in the units of Mbps

4.2.2.9.

Displaying the Current Interval Counter

This menu selection displays

Current Interval Performance Counters

, useful for monitoring network

integrity. To display performance counters from the

STAT

menu, use the toggle switch/pushbutton to

select the

DS3

menu item and then choose the

CIC

menu item. The module records the

Current

performance over 15 minute and 24 hour intervals, which restart once they have expired. The
corresponding status is displayed by selecting either the

15m

24h

menu item. To display the current

timer value, select

TIME

STAT

DS3

CIC

15m
24h

TIME

The following indications are possible:

899/1440

Timer value in seconds or minutes, for 15m or 24h
timers, respectively

The following menu is available to display performance counters:

STAT

DS3

CIC

15m
24h

LOSS
OOF
AIS
RAI
IDLE
SEF

The following indications are possible:

LOSS

Signal Loss

OOF

Out Of Frame

AIS

Alarm Indication Signal

RAI

Remote Alarm Indication

IDLE

DS3 Idle Signal

SEF

Severely Errored Frame

Summary of Contents for 7780ASIB2-DS3/E3





































Search results

Summary of Contents for 7780ASIB2-DS3/E3

Reviews:

Related manuals for 7780ASIB2-DS3/E3

Brands by name

Popular brands

evertz 7780ASIB2-DS3/E3, Manual

Search results

Summary of Contents for 7780ASIB2-DS3/E3

Reviews:

Related manuals for 7780ASIB2-DS3/E3

Brands by name

Popular brands