manualshive.com logo in svg

evertz 7780ASIB2-DS3/E3, Manual

Share
Download
evertz 7780ASIB2-DS3/E3 Manual Download Page 5

7700 MultiFrame Manual 

7780ASIB2-DS3/E3 2 Channel ASI + Ethernet DS3/E3 Transceiver 

 Revision 

2.0 

Page - 1 

1. OVERVIEW 

The 7780ASIB2-DS3/E3 is a 

Vista

LINK

®

 enabled, DS3/E3 (44.736Mb/s) transceiver for DVB-ASI video 

signals.  The card also has a built-in 10/100 Base T Ethernet transceiver port.  This single card combines 
2 asynchronous DVB-ASI signals using Time Domain Multiplex (TDM) technology. A companion 
7780ASIB2-DS3/E3 card acts as a demultiplexer for the incoming signal and converts them back to 
separate ASI video feeds, while utilizing a separate DS3/E3 link for the outgoing signal. 
 
Monitoring and control of card status and parameters are provided locally at the card edge or remotely via 

Vista

LINK

®

. 

 
The 7780ASIB2-DS3/E3 occupies two card slots in the 3 RU frame, which will hold up to 7 modules, or 
three modules in a 1RU frame.   

 
Features: 

•

 

Transports signal over DS3/E3 data rates (44.736Mb/s) 

•

 

Single card TDM multiplexer and demultiplexer for two bi-directional asynchronous DVB-ASI 
signals 

•

  Built-in Ethernet transceiver with one 10/100 Base-T port with FBM (Flexible Bandwidth 

Management) 

•

 

Interfaces directly to DS3/E3 infrastructure 

•

 

Signal transport uninterrupted by loss of any DVB-ASI input feed 

•

 

Wide input frequency range tolerance (±50ppm) 

•

 

Comprehensive signal and card status monitoring via four character card-edge display 

•

 

Vista

LINK

®

 – enabled offering remote monitoring, control and configuration capabilities via SNMP. 

Vista

LINK

®

 is available when modules are used with the 3RU 7800/7700 series multifame, a 

7700FC 

Vista

LINK

®

 Frame Controller module in slot 1 of the frame using the 9000NCP Network 

Control Panel or Evertz 

Vista

LINK

®

 PRO or other third party SNMP manager software 

•

 

Automatic coaxial equalization up to 250m (Belden 1694A or equivalent cable) 

•

 

Fully hot-swappable from front of frame with no coax disconnect/reconnect required 

 

Summary of Contents for 7780ASIB2-DS3/E3





































Reviews:

No comments

Brands by name

Popular brands

Load more brands