manualshive.com logo in svg

evertz 7780ASIB2-DS3/E3, Manual

Share
Download
evertz 7780ASIB2-DS3/E3 Manual Download Page 30

7700 MultiFrame Manual 

7780ASIB2-DS3/E3 2 Channel ASI + Ethernet DS3/E3 Transceiver 

Page - 26

 Revision 

2.0 

6.2. 

CONFIGURING THE MODULE FOR FIRMWARE UPGRADES 

The 7780ASIB2-DS3/E3 card can be configured for firmware upgrades using the UPGRADE jumpers or 
with the serial port ‘u’ command as described below.

 

 

6.2.1.  Using the Upgrade Jumper 

UPGRADE: 

  The UPGRADE jumper is used when firmware upgrades are being performed on the 

module.  For normal operation it should be installed in the 

RUN

 position.  See the 

Upgrading Firmware

 section of this manual for more information. 

 

To upgrade the firmware in the module unit pull it out of the frame.  Move the UPGRADE 
jumper into the 

UPGRADE 

position.  Install the Upgrade cable provided (located in the vinyl 

pouch in the front of this manual) onto the SERIAL header at the card edge.  Re-install the 
module into the frame.  Run the upgrade as described in the 

Upgrading Firmware

 section in 

the front of this manual binder.  Once the upgrade is complete, remove the module from the 
frame, move the UPGRADE jumper into the 

RUN

 position, remove the upgrade cable and 

re-install the module.  The module is now ready for normal operation. 

 

6.2.2.  Upgrade Serial Port Command 

Install the Upgrade cable provided (located in the vinyl pouch in the front of this manual) onto the SERIAL 
header at the card edge of the card to be upgraded. Connect this cable to your computer and run a 
terminal program as described in the 

Upgrading Firmware

 section in the front of this manual binder.  Type 

in “u” without the quotes and hit the enter key.  Follow the prompts that are presented on your terminal 
screen and proceed to download the new firmware specified for this card. 

Summary of Contents for 7780ASIB2-DS3/E3





































Reviews:

No comments

Brands by name

Popular brands

Load more brands