background image

Operation – Important Safety Information (continued) 

 

18

Chemical accident procedures: 

 

WARNING 

 

 

Before you use the pump, review the following information with regard to handling 
accidents. 
Chemical spills, pump leaks, personal contamination, and poisoning are accident situations 
which you may encounter.   

All require an immediate response – See instructions below.

 

 

 

Pump leak 

In the event that the pump develops a leak while spraying chemicals, you 
must immediately stop spraying

.   

 

Turn off power to the pump and follow the directions below, as 
applicable. 

Bodily chemical 
contact 

Personal contamination can occur when chemicals splash, spill, or spray 
directly onto a person.   

 

1.  Follow the emergency first aid instructions on the chemical label listed in 

the “First Aid” or “Statements of Practical Treatment” section. 

 

General procedures include: 
a) Eyes – immediately flush with water or follow other directions as 

specified on the chemical label. 

b) Skin – immediately wash all contaminated skin surfaces with soap  

and water, or follow directions as specified on the chemical label. 

c) Clothing – remove contaminated clothing immediately.  Dispose of 

heavily contaminated clothing per the instructions on the chemical 
label for safe chemical/container disposal.   

 

2.  Seek medical advice if instructed on the label, or if the victim experiences 

symptoms of harmful effects such as burning, swelling, nausea, chest 
pain, difficulty breathing, dizziness or confusion.  When seeking medical 
advice, be sure to bring the chemical product label. 

Poisoning by 
ingestion or 
inhalation 

In case of poisoning from ingestion or inhalation

 
IF THE VICTIM HAS COLLAPSED OR IS NOT BREATHING, 

CALL 

911

.   Otherwise: 

 
1. If you are the victim, immediately seek assistance from nearby personnel 

because you may become incapacitated. 

 
2. Follow the emergency first aid instructions on the chemical label in the 

“First Aid” or “Statement of Practical Treatment” section. 

 
3. Call a poison control center for further advice.  

In the U.S., call 1-800-

222-1222 to be automatically linked to the nearest certified poison 
control center.  

Have the chemical label available for reference. 

 

Chemical spills 

Chemical spills must be quickly contained and properly cleaned up.   

 
Refer to the chemical label for any specific clean-up instructions with regard 
to the chemical spilled. 
 
 

Summary of Contents for EFHP-2000

































Reviews: