EVBox Troniq Installation Manual Download Page 5

 

 

 

 
 

Page 5/34 

 

2.

 

TRANSPORT 

The following commissioning requirements are given for information and do not commit in anyway, 

EVBox  responsibility.  The  charger  should  be  installed  by  a  qualified  installer,  and  be  carried  out 

"according to state of the art" and adapted to the specificities of the installation site and the own 

countries rules. 

 

2.1

 

Load 

In case that the charger comes with storage system, its maximum total weight excluding packaging is 

estimated to be 450 kg. 

 

2.2

 

Packaging 

The charger will be protected against external hangings with safety conventional material. However, 

you must be careful not to use tools that can get through the packaging and damage the charger. 

 

2.3

 

Logistics 

The lower support of the charger is equivalent to the shape of a pallet. A lifting system pallet type is 

therefore sufficient to move and install it. However, be careful to remove the charger from the delivery 

van; it will eventually be necessary to provide a lifting system with a necessary working height (about 

1,3 m). 

 

The transportation and the set up can only be done in an appropriate manner: 

 

-      For moving, using of a pallet truck with a charge capacity of at least 1000 Kg. 

-      For placement, using a pallet truck (> 150 mm of rising) or a forklift truck with a charge capacity of 

at least 1000 Kg, and before that it is necessary to check the stability of the charger on the machine. 

 

2.4

 

Warnings! 

To ensure secure installation, make sure to follow these recommendations and thus avoid:  

-

 

Transporting the charger in a manner other than upright. 

-

 

Carrying the charger in any other ways than those indicated above. 

-

 

Using a lifting device while the charger is s electrically connected. 

-

 

Using a crane type hoist that would not support the weight of the charger. The use of slings is 
allowed by taking the charger through the lower support. 

-

 

The charger’s centre of gravity is located in the central position, thus care is needed when 
handling.

 

 

Summary of Contents for Troniq



































Reviews: