background image

EXP120K1-HT 120KW DC Charger

Configuration:

CCS2

CHAdeMO

AC tipo 2

Component

Description

Charge controller

IMMSU-D charging cont PLC cont insulation detector

Upper controller

IMMU2

Power module

REG75030G or REG50040G – optional configuration: 1~8 pcs

DC charging gun

200A CCS-2  / 125A CHAdeMO

AC charging gun

32A type 2 AC

DC power distribution

Standard system 120KW.
The positive and negative DC output are provide with NO contractors and fuse protection. 
The charger module has a built-in discharge circuit.

AC connector distribution

AC connector breaker and contactor, type B RCD (opcional)

Temperature control system

Heat exchange system

Card reader

RFID

Metering

2 DC energy meter and 1 AC energy meter

HMI

7 inch TFT touch screen display and 5 LED indicators

Módem wireless LTE

1   wireless   communication   (   optional,   insert   the   LTE   modem   card   into   IMMU2   upper
controller), 1 LAN

1.3  Technical parameters

Parameter

Description

Condiciones
ambientales

Operating temperature

1

-20°C~+45°C

Transportation / storage temperature

-40°C~+70°C

Relative humidity

5%RH~95%RH (with condensation)

Atmospheric pressure

80KPa~110KPa

Overvoltage category

II

Altitude

2000 m

Impact resistante

The impact resistance is 20J (5Kg, 0.4m). After the impact
the performance must not be affected. Make sure that the
IP class has not been affected, check the door fixing point
are not damaged and the internal components are not in
contact with any parts.

Mechanical
parameters

Dimensions (W × H ×D)

700 x 1750 x 760

mm

Weight (kg)

210Kg   (without   power   module),   power   module   weight
11kg each.

Note 1:

 The DC charger provides full output power up to 45ºC, output power decrease 5% above 45ºC.

The protection level of the DC chergar is IP65. But for charging safety it should not be used during rain or snow if water can
reach the charger connector.

EV Vision – Porto – Portugal – 

www.ev-vision.com

 – Support service: (+351) 229 999 230

All rights reserved. This manual may be changed without prior notice. - V 1.0 – 2019/08/10 – Pag. 7 de 25

Summary of Contents for EXP120K1-HT


























Reviews: