Eurotherm TC3001 User Manual Download

Page: 12 / 79

Transit Inspector Pro

Deploying Module

User Guide

Table 4

: One Module configuration required parameters

Parameter

Requirements

Windows XP Professional (Service Pack 2).

Mainboard

See

SecurOS Installation Guide

CPU

Intel Pentium IV 2.4 GHz or higher.

RAM

512 MB or more.

Video board

128 MB or more.

SecurOS software

Administrator workstation software.

Table 5

: Two or more Modules configuration required parameters

Parameter

Requirements

Windows XP Professional (Service Pack 2).

Mainboard

See

SecurOS Installation Guide

CPU

Intel Pentium IV 3.0 GHz or higher.

RAM

512 MB or more.

Video board

128 MB or more.

SecurOS software

Administrator workstation software.

3.2

Installing Hardware

Types and quality of video capture boards depend on used video cameras (see

SecurOS Installation

Guide

3.2.1

Installing video cameras

Module recognizes carriage numbers from an incoming video stream.

Note:

Connecting video cameras are fully described in

SecurOS Installation Guide

The video cameras have to be installed directly next to the permanent way. The best camera position is
frontal view on carriage number. The optimal distance from the camera to the carriage is determined

www.isscctv.com

Summary of Contents for TC3001
















































































Search results

Summary of Contents for TC3001

Reviews:

Related manuals for TC3001

Brands by name

Popular brands

Eurotherm TC3001, User Manual

Search results

Summary of Contents for TC3001

Reviews:

Related manuals for TC3001

Brands by name

Popular brands