Eurotherm 216 User Manual Download Page 16

Page: 16 / 40

P 1 1

P 1 1 =

= Safety lock

Safety lock

0 =

No parameter protection.The device is

always in “unlock” condition and all the
parameters can be always modified.
1 =

None parameter, with the exception of

parameters from

, can be modified.

2/499 = This combination numberis a secret
value, to be used in operative mode, to place
the device from the “lock” to the “unlock”
condition (the parameters from

are not

subjected to the lock/unlock rule)
500/999 = This combination number is a secret
value, to be used in operative mode, to place
the device from the “lock” to the “unlock”
condition (the parameters from

and

AL.1

–

AL.2

are not subjected to the

lock/unlock rule)

P 1 2

P 1 2 =

= Out maximum rate of rise

Out maximum rate of rise

This limit will be used if

is different from 0

only.
Programmable from 1 to 25% of the out signal
per second.
Over 25%/s the instrument displays “

InF

” to

indicate the exclusion of the limitation.
This limit have no effect if the selected contol
algorithm is ON/OFF type (PB=0)

P13 – FILTER ON INPUT MEASURE

OFF

= Filter disabled

= Filter enabled

P14 =

P14 = Protected parameters display

Protected parameters display

This parameter is available if P11 is not 0.
This parameter enables/disables the display of
the protected parameter during "operative mode".

OFF

= the protected parameters are not
displayed

= the protected parameters are displayed

P 1 5

P 1 5 ----- SMART function enabling/

SMART function enabling/

disabling

0 = The SMART function is disabled
1 = SMART function enabling/disabling is

NOT

NOT protected by the safety code.

2 = SMART function enabling/disabling is

protected by the safety code.

P16

P16 ----- Maximum value of the proportional band

Maximum value of the proportional band

Maximum value of the proportional band
automatically settable by the

automatically settable by the

automatically settable by the
SMART function

SMART function

This parameter is available if P15 is not 0. It can
assume the following values:

model 0316:

between P17 or P18 and 99.9%

model 0216:

between P17 or P18 and 100.0%

P17

P17 ----- Proportional minimum band value

Proportional minimum band value

Proportional minimum band value
automatically settable by the

automatically settable by the

automatically settable by the
SMART function ( one control out

SMART function ( one control out

SMART function ( one control out
only)

only)

This parameter is only displayed if P5 is not 5 and
P15 is not 0.
It may be programmed from 1.0% to the value of
P16.

P 1 8

P 1 8 ----- Proportional minimum band value

Proportional minimum band value

automatically settable by the

automatically settable by the
SMART function (two control outs,

SMART function (two control outs,

SMART function (two control outs,
heating/cooling)

heating/cooling)

This parameter is only present if P5 is 5 and P15
is not 0.
This parameter may be programmed from 1.5%
to the value of P16.

02-0316-1-DER.pmd

22/04/2004, 16.19

Summary of Contents for 216









































Search results

Summary of Contents for 216

Reviews:

Eurotherm 216, User Manual, Page: 16 / 40

Search results

Summary of Contents for 216

Reviews: