ETLU4G03
Rev. 003
3 )
3 )
3 )
3 ) First time operation of ETLU4G03
First time operation of ETLU4G03
First time operation of ETLU4G03
First time operation of ETLU4G03
ETLU4G03 is shipped with all the main switches set in the correct configuration. So when the Transmitter
is connected to mains network it will be turned off.
Prior to switch on the transmitter ensure that all R.F. connections have been carried out properly.
Prior to switch on the transmitter ensure that all R.F. connections have been carried out properly.
Prior to switch on the transmitter ensure that all R.F. connections have been carried out properly.
Prior to switch on the transmitter ensure that all R.F. connections have been carried out properly.
Check for video modulation signal presence prior to start with switch on procedure.
Once the Transmitter unit is properly installed follow the steps below for the first time operation.
•
Turn on “Main Supply” switch of the Transmitter unit. Three phase monitor LEDS of each Block
should switch on showing three phases presence.
•
Turn on “Internal Single Phase” switch of the Transmitter unit. This switch provides power supply to
230V a.c. internal modules of the Transmitter unit (Exciters, Transmitter Supervisor & Controller,
internal cooling blowers).
•
Turn on “Amplifier” switches of the Transmitter unit. These switches provide power supply to amplifier
modules of the Transmitter unit. Each amplifier has its own switch so each amplifier module can be
turned off individually.
•
Turn on the “On/Off” switch on the front panel of each Exciter.
Now the Transmitter unit is completely switched on. The display of each module should be operating.
•
Make sure there are no alarm status for the Transmitter unit.
•
Check that exciter modules are set in “Local” mode and in “Off” status.
Now is possible to enable R.F. output power from the Transmitter unit.
•
Enable R.F. output power of the Transmitter unit by means of “TX On” command on Transmitter
Supervisor & Controller unit.
Refer also to “ETL0700TA Transmitter Supervisor & Controller Operating and Technical Manual” for
Refer also to “ETL0700TA Transmitter Supervisor & Controller Operating and Technical Manual” for
Refer also to “ETL0700TA Transmitter Supervisor & Controller Operating and Technical Manual” for
Refer also to “ETL0700TA Transmitter Supervisor & Controller Operating and Technical Manual” for
Supervisor command explanation.
Supervisor command explanation.
Supervisor command explanation.
Supervisor command explanation.
•
By means of Transmitter Supervisor & Controller, set “TX Exciter A On/Off” and “TX Exciter B
On/Off” to “On” or “Off” according to the actual position of the changeover switch. Changeover
position is shown in Transmitter Supervisor & Controller main page.
•
Set the on-air exciter (exciter selected to be “on-air” by changeover switch) to “On” status by means
of the soft key of the exciter module.
For safety reasons the Transmitter unit is factory set in order to provide very low level of R.F. output
For safety reasons the Transmitter unit is factory set in order to provide very low level of R.F. output
For safety reasons the Transmitter unit is factory set in order to provide very low level of R.F. output
For safety reasons the Transmitter unit is factory set in order to provide very low level of R.F. output
power at the first time operation.
power at the first time operation.
power at the first time operation.
power at the first time operation.
To set the nominal R.F. output level follow the steps below. The following procedure must be followed to
The following procedure must be followed to
The following procedure must be followed to
The following procedure must be followed to
make sure that all the R.F. connections are properly done.
make sure that all the R.F. connections are properly done.
make sure that all the R.F. connections are properly done.
make sure that all the R.F. connections are properly done.
Refer also to “ETL3100RT Operating and Technical Manual” for Exciter command explanation.
Refer also to “ETL3100RT Operating and Technical Manual” for Exciter command explanation.
Refer also to “ETL3100RT Operating and Technical Manual” for Exciter command explanation.
Refer also to “ETL3100RT Operating and Technical Manual” for Exciter command explanation.
•
Check again video modulation signal presence.
Page 16
CMANU4G03
Jul 2013
Summary of Contents for ETLU4G03
