Eurotech DuraMAR 2150 User Manual Download Page 10

Page: 10 / 38

DuraMAR 2150 – User’s Manual

System interfaces

Front panel connector layout

USB firmware

upgrade port

HSDPA SIM

LEDs

CPU console

Cisco console

GND

GSM/GPRS SIM

Figure 2.

Front panel layout (with protection cover removed)

Service interfaces

Some service interfaces are provided on the front panel of the system under a protection cover. It is possible
to remove this cover by removing the two Torx screws.

Warning:

While the protection cover is removed it is not possible to maintain the IP protection
grade

The service interfaces can be used for debugging, firmware uploading, system configuration and diagnostics:

•

SIM card holder for HSDPA

•

SIM card holder for GSM/GPRS

•

CISCO 3200 ISR serial console port

•

ECC serial console port

•

USB1.1 port of embedded controller for firmware upgrading

LED indicators

On the front panel of the system there are 6 LED indicators with functions as described below.

LED Number

Function

Comments

Not Connected

Power Good

+12 V present

GSM activity

Software programmable

HSDPA activity

Software programmable

Power #1 On

5 V present

Power #2 On

3.3 V present

Summary of Contents for DuraMAR 2150







































Search results

Summary of Contents for DuraMAR 2150

Reviews:

Related manuals for DuraMAR 2150

Brands by name

Popular brands

Eurotech DuraMAR 2150, User Manual

Search results

Summary of Contents for DuraMAR 2150

Reviews:

Related manuals for DuraMAR 2150

Brands by name

Popular brands