Euresys 1633-LH Hardware Manual Download Page 177

Page: 177 / 210

177

3617 HD26F I/O Extension Module - TTL-CMOS5V

Compatible with

The

3617 HD26F I/O Extension Module - TTL-CMOS5V

accessory is an

I/O extension module

be used with above listed frame grabber products.

This module adds a total of 24 I/O ports with a configurable mix of 2 types:

□

single-ended 5 V compliant TTL input

□

single-ended 5 V CMOS output

The module:

□

is powered by the frame grabber through the I/O EXTENSION cable.

□

is software configurable. There are no jumpers.

□

provides a persistent configuration. The last configuration is automatically restored at
power-up

3617 HD26F I/O Extension Module - TTL-CMOS5V

3602 Coaxlink Octo

3603 Coaxlink Quad CXP-12

3603-4 Coaxlink Quad CXP-12

3620 Coaxlink Quad CXP-12

JPEG

3620-4 Coaxlink Quad CXP-12 JPEG

3621 Coaxlink Mono CXP-12

3621-LH Coaxlink Mono CXP-12 LH

3622

Coaxlink Duo CXP-12

3622-LH Coaxlink Duo CXP-12 LH

and

3625 Coaxlink QSFP+

eGrabber

Hardware Manual

Summary of Contents for 1633-LH



















































































































































































































Search results

Summary of Contents for 1633-LH

Reviews:

Related manuals for 1633-LH

Brands by name

Popular brands

Euresys 1633-LH, Hardware Manual

Search results

Summary of Contents for 1633-LH

Reviews:

Related manuals for 1633-LH

Brands by name

Popular brands