background image

Operation

35

Presets (Vivid, Lustr+, Fire, Ice, and Studio HD)

A Preset is a single, static look or color mix. The Desire Series fixtures come with 24 default 
configurations. Only one Preset can be active at a time. You can activate any of the Preset color mixes 
and customize each one through your RDM device. The following table lists the default Preset color 
mixes. 

Presets (Studio Daylight, Studio Tungsten)

The Desire Studio Daylight and Studio Tungsten fixtures come with 24 available slots for Presets. There 
are no default Presets that come pre-configured from the factory. You can activate any of the Presets 
and customize each one. Only one Preset can be active at a time. Studio Daylight and Studio Tungsten 
fixtures have Presets that you can define both Intensity and Strobe values. 

Preset

Default Color

1

White

2

Warm

3

Cool

4

Minus Green

5

Lite  Pink

6

Lite Gold

7

Yellow

8

Dark Straw

9

Dark Amber

10

Orange

11

Red

12

Med Pink

13

Dark Pink

14

Magenta

15

Purple

16

Dark Lavender

17

Deep Purple

18

Clear Blue

19

Lite Blue

20

Med Blue

21

Primary Blue

22

Blue-Green

23

Lite Green

24

Green

Summary of Contents for Desire D40

















































Reviews: