
APPENDIX A
SOFTWARE COMMANDS
Revised: 10 Oct 2017
APX A-6
ESTeem Models 195MHC
rfpower (1-8)
This command sets the output power on the ESTeem 195M/H/C radio modem. Each increase in value represents 0.5 watts of
output power. Factory default = 8 (4 Watts).
1 = 0.5 Watts
2 = 1.0 Watts
3 = 1.5 Watts
4 = 2.0 Watts
5 = 2.5 Watts
6 = 3.0 Watts
7 = 3.5 Watts
8 = 4.0 Watts
route (l#,r1,r2,r3,)
The route sets up the route table in the ESTeem. This command is used in conjunction with the append command to configure
the routing table in the ESTeem 195M/H/C wireless modem. See Chapter 4 (Repeating) for complete details.
l #
=
User defined route number. Route numbers 1 to 64 may be used.
r1
= Address of first repeater. Address numbers from 1 to 254 may be used.
r2
= Address of second repeater. Address numbers from 1 to 254 may be used.
r3
= Address of third repeater. Address numbers from 1 to 254 may be used.
rssi
This command will display the status of the received signal strength indication (rssi). The values displayed in dBm.
instantaneous, noise floor, last valid (dBm)
save
The save command. The execution of this command stores the current command values and switches.
Note:
Please wait approximately two seconds
after
executing the SAVE command before turning off power to the ESTeem.
s/n
Serial Number command. When executed from the Command Model will output the ESTeem serial number of the unit that is
defined at the time of manufacturer.
sdi
Sets the serial device interface (sdi) for the ESTeem 195M/H/C. Any serial port not configured as the sdi can be used as a
console port for programming. The sdi can also be placed in console mode by entering three pluses (+++) in the port within
three seconds of a reboot of the ESTeem 195C or 195M. Factory default = 2 (Port 3
–
RS-232 with Full Handshake Lines)
0 = No serial data interface (All console ports)
1 = RS-232 Port 4 (3 wire RS-232 only with remote power)
2 = RS-232 Port 3 (Full RS-232 with hardware handshaking)
3 = RS-485 Port 1
4 = RS-422 Port 2
5 = TCP Socket Port 2 (Custom software interface required)
6 = UDP Socket Port 2 (Custom software interface required)
Note: Port pin-out information found in Appendix B (Interface Ports)
Technical Tip
:
A three second delay is added
after a reset before the ESTeem 195C or
195M will process any data through the serial
interface. This time allows entry of the
console break sequence to program (+++).
Summary of Contents for 195C
