manualshive.com logo in svg

Essilor PRO-E 600, User Manual

Share
Download
Essilor PRO-E 600 User Manual Download Page 26

The use of the high-base bevel depends on two parameters: the frame and the lens.

•

Concerning the lens, the main constraint is the thickness of the nasal and temporal edges.

•

Concerning the frame, the crucial elements are the bridge and shape of the groove. The hinge is an
additional factor in the case of a metal frame, the arms for a plastic frame.

For   this   job,   the   lens   base   must   always   match   the   frame   base   perfectly.   Too   great   a   difference

between the two could be detrimental to the quality of your job.

Cross-sectional view of a high-base bevel

1: Shelf bevel value 

2: Width of the flat side of the bevel 

3. Front surface tracking value

a. Captioned screens

1.

High-base bevel “front surface tracking” screen

2.

Work area

Image of the shape to be edged:

 Frame shape at bottom of groove

 Bevel trajectory on rear surface

U

SER

 M

ANUAL

> II. E

DGING

 

A

 

LENS

 

29

Pro-E 600 > v1 -02.17

Summary of Contents for PRO-E 600

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands