manualshive.com logo in svg

Essilor PRO-E 600, User Manual

Share
Download
Essilor PRO-E 600 User Manual Download Page 21

6.

Bevel distribution value

Distribution value modifiable for:

◦

front/rear surface tracking

◦

a distributed bevel

◦

lens curve tracking

7.

Modify the selected value

Reduce or increase the distribution value.

8.

Bevel trajectory

Flat representation of the lens making it possible to assess the distances between the bevel crest and the

front & rear surfaces of the lens.

9.

Trajectory modification

◦

 General modification of the bevel curve

◦

 Modification of the bevel curve at a particular point

◦

 Displacement of the bevel curve

10.

Navigation

◦

 Stop the cycle

◦

Back to the main edging screen

◦

Start the edging cycle

c. Customized beveling

The use of the customized bevel depends on 2 parameters: the frame and the lens. Before starting your job,

identify the major constraint.

B

EVEL

F

RAME

L

ENS

A

DVANTAGES

Classic

Lens for which the front surface 

base is approximately equal to 

the frame base.

Makes it possible to do an aesthetically pleasing 

job. The lens material does not protrude beyond 

the front of the frame.

Classic

Lenticular lens

&

, Executive lens

&

Makes it possible to do a job with specific lenses.

Classic

Thin lens

Makes it possible to balance out the bevel when 

thin lenses are used.

Flat base

High base

Thin lens for which the front 

surface base is approximately 

equal to the frame base. 

Makes it possible to retrieve the frame base in a 

pattern tracing (base = 0).

Particular groove 

(groove with 

meniscus

&

)

Thin lens for which the base is 

approximately equal to the 

meniscus of the groove.

Compliance with original shape.

Job using a specific frame.

Pro-E 600 > v1 -02.17

24

U

SER

 M

ANUAL

> II. E

DGING

 

A

 

LENS

 

Summary of Contents for PRO-E 600

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands