manualshive.com logo in svg

Essilor PRO-E 600, User Manual

Share
Download
Essilor PRO-E 600 User Manual Download Page 16

> Scan the barcode using the barcode reader (optional).

Always lock down your 2 lenses before proceeding with the edging. If a job in the course of modification on

the tracer (display of the symbol   beside the reference) is called up on the edger, a warning message is

displayed.

> Press

 to continue and display the job on the edger. The modifications underway are then ignored.

> Press

 to prevent the display of the job and finish the modifications underway on the tracer.

A reminder of the type of posiblock required is displayed on the shape. It is crucial to use the proper

accessory to edge the lens. Otherwise, an error message is displayed at the start of the cycle.

c. Lens set-up and feeling

 Prerequisite: the lens must be centered and blocked before placing it in the edger.

Check that the posiblock holder and the stop correspond to the posiblock used. Otherwise, you will need

to remove them from the lens clamp shafts and replace them with the tools matching the diameter of the

posiblock.

•

For a 22 mm posiblock

•

For an 18 × 14 mm posiblock

Place the lens in the posiblock holder.

Place the metal peg of the posiblock upwards and the positioner downwards: a magnet is used to

hold the lens in position on the axis.

1

2

U

SER

 M

ANUAL

> II. E

DGING

 

A

 

LENS

 

19

Pro-E 600 > v1 -02.17

Summary of Contents for PRO-E 600

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands