Essilor Instruments VISION-R 700 User Manual Download Page 68

Page: 68 / 128

Once the condition is selected, start the test.

On the touch screen by pressing on [Start].

On the console keyboard, by pressing on the central button.

The center part of the screen appears grayed out. It is no longer possible to modify the values of

controlled settings, the masks, the filters or the adjustments of the instrument.

The Red/Green smart test is shown in the display area in the bottom of the console’s touch screen.

The corresponding table of optotypes is displayed on the test presentation screen.

SER

MANUAL

> P

ERFORMANCE

TESTS

DURING

REFRACTION

EXAMINATION

Vision-R 700 - Essilor automatic phoropter > V1 - 09-2020

Summary of Contents for VISION-R 700

































































































































Search results

Summary of Contents for VISION-R 700

Reviews:

Related manuals for VISION-R 700

Brands by name

Popular brands

Essilor Instruments VISION-R 700, User Manual

Search results

Summary of Contents for VISION-R 700

Reviews:

Related manuals for VISION-R 700

Brands by name

Popular brands