Essilor Instruments VISION-R 700 User Manual Download Page 107

Page: 107 / 128

[Date Format]

Sets the display of the console date format:

Year/Month/Date > [YY/MM/DD]
Month/Date/Year > [MM/DD/YY]
Date/Month/Year > [DD/MM/YY]

[Time Format]

Sets the display of the console time format

[Date]

Sets the display of the console date format

Once the adjustments are made, press on:

to confirm.

to cancel.

f. Backups restore

The backups restore menu has two pages:

1. Backup
2. Restore

1 - Page [Backup]

Export of refraction head data to an USB key

Export of all the instrument data

Settings export

Export of the technician data

Export of tests, favorites and test programs

Statistics exportation

SER

MANUAL

> I

NSTRUMENT

SETTINGS

107

Vision-R 700 - Essilor automatic phoropter > V1 - 09-2020

Summary of Contents for VISION-R 700

































































































































Search results

Summary of Contents for VISION-R 700

Reviews:

Related manuals for VISION-R 700

Brands by name

Popular brands

Essilor Instruments VISION-R 700, User Manual

Search results

Summary of Contents for VISION-R 700

Reviews:

Related manuals for VISION-R 700

Brands by name

Popular brands