Essilor Instruments DELTA User Manual Download Page 96

Page: 96 / 187

For more information, consult the section Edging a lens > Perform a polishing

(

p.121)

and Edging

a lens > Perform a chamfering

(

p.121)

Close the door.

Press

The tightening then the feeling of the lens start consecutively.

The edging cycle starts.

When the edging cycle is finished, the retouch screen is displayed.

Press

to release the lens.

If necessary, retouch the lens.

Otherwise, start edging the second lens. Select the lens directly on the screen, on the left or right of the

work area.

The edging screen for the second lens is displayed. All finishes chosen and the modifications made

are kept.

b. Legend screen for customized bevels

Automatic bevel

SER

ANUAL

> VII. E

DGING

LENS

Delta - Edging System > V1- 02-2020

Summary of Contents for DELTA




























































































































































































Search results

Summary of Contents for DELTA

Reviews:

Essilor Instruments DELTA, User Manual, Page: 96 / 187

Search results

Summary of Contents for DELTA

Reviews: