manualshive.com logo in svg

Essilor Instruments DELTA, User Manual, Page: 30 / 187

Share
Download
Essilor Instruments DELTA User Manual Download Page 30

Input the wrap angle and the frame base.

   

   

Press the 

 button.

   

   
   

   

The following screen is displayed:

   

   

 

 

   

   
   

   

   

   

 

 

 

 

   

   

Select the wrap angle value 

 to modify it. 

   

   

   

   

The value is displayed in red. 

   

   

 

 

 

 

   

   

Place the frame on the screen:

   

   

 

 

   

   

•

The vertical blue line must be in the center of the frame

•

The bridge of the frame superimposed on the base line.

   

   

 

 

   

   
   

   
   

  

 

 

   

   

Use the 

 and 

 buttons to align the light blue lines with the nasal and temporal ends of the rims.

   

   

 

 

>

>

1

2

3

4

Delta - Edging System > V1- 02-2020

32

U

SER

 M

ANUAL

> III. C

ARRY

 

OUT

 

AN

 

OPTICAL

 

TRACING

Summary of Contents for DELTA




























































































































































































Reviews:

No comments