manualshive.com logo in svg

Essilor Instruments DELTA, User Manual, Page: 118 / 187

Share
Download
Essilor Instruments DELTA User Manual Download Page 118

6. P

ERFORM

 

A

 P

OLISHING

 

 

Press the 

 button to activate/deactivate polishing.

 

 

L

ENS

 

MATERIAL

A

VAILABLE

 

OPTIONS

 

 

The polishing option is pre-selected and is strongly recommended by 

the manufacturer to prevent small cracks.

 

Make sure you select the correct type of material for MHI (> 1.5) or 

Tribrid lenses and never polish a lens of this type without water. 

Otherwise, the polishing wheel could suffer irreversible damage.

 

The polishing option is pre-selected.

7. C

HAMFERING

 

 

The chamfer, also called counter-bevel, removes the sharp edge of the lens.

•

Standard value of a small chamfer: 0.20 mm

•

Standard value of a large chamfer: 0.40 mm

 

 

Before you select a type of chamfer, make sure it is compatible with the lens characteristics:

U

SER

 M

ANUAL

> VII. E

DGING

 

A

 

LENS

121

Delta - Edging System > V1- 02-2020

Summary of Contents for DELTA




























































































































































































Reviews:

No comments