Essilor Instruments DELTA User Manual Download Page 157

Page: 157 / 187

6. S

TATISTICS

AND

TECHNICAL

HISTORY

THE

EDGER

This menu enables you to visualize the number of cycles carried out by the edger. It also gives you access to

the technical history.

•

Edger cycles

(

p.160)

•

Technical history log and errors

(

p.161)

a. Edger cycles

From the work screen, select

to visualize the number of cycles performed by

the edger.

The following screen is displayed:

Partial counter

The replacement of a worn tool with a new one resets the partial counter(s) to zero.

Total counter

Edging operations

Number of edging, drilling and finishing operations performed depending on the lens material:

◦

Roughing

◦

Bevels

◦

Flat-edge finish

◦

Grooves

◦

Drill-holes/slots

◦

Notches

◦

Polishing

◦

Chamfers

Drilling

Number of drilling operations performed for each lens material, according to the drill bit used.

Touch screen calibrations

Number of lenses cut

Delta - Edging System > V1- 02-2020

160

SER

ANUAL

> IX. M

AINTENANCE

AND

SERVICING

Summary of Contents for DELTA




























































































































































































Search results

Summary of Contents for DELTA

Reviews:

Essilor Instruments DELTA, User Manual, Page: 157 / 187

Search results

Summary of Contents for DELTA

Reviews: