Essilor Instruments DELTA User Manual Download Page 134

Page: 134 / 187

The following screen is displayed:

Frame types

◦

Metal

◦

Plastic

◦

Optyl

◦

Drilled / Grooved / Flat

Lens materials

◦

Plastic

◦

Polycarbonate

◦

MHI

◦

Trivex

◦

Glass

◦

Tribrid

Adjust the lens diameter

a. Press the value to be modified.

> The numeric keypad is displayed.

b. Enter the new value.

◦

Negative value: the diameter will be smaller

◦

Positive value: the diameter will be larger

c. Press

to confirm.

Once the modification is made, press

to return to the work screen.

b. Adjusting the position of the bevel and groove

After edging a lens, if the position of the bevel or groove always seems too close to the front or rear surface,

you can adjust it.

To access this menu from the work screen of your edger, select

SER

ANUAL

> VIII. S

THE

PRODUCT

137

Delta - Edging System > V1- 02-2020

Summary of Contents for DELTA




























































































































































































Search results

Summary of Contents for DELTA

Reviews:

Essilor Instruments DELTA, User Manual, Page: 134 / 187

Search results

Summary of Contents for DELTA

Reviews: