manualshive.com logo in svg

Essilor Instruments DELTA, User Manual, Page: 76 / 187

Share
Download
Essilor Instruments DELTA User Manual Download Page 76

Cancelling a modification

•

Press 

 once to cancel the last modification made to the shape.

•

Press 

 twice consecutively to return to the original shape. 

 

 

Once the shape is modified, press 

 to save and go back to the centering screen. 

d.  Retouching a shape

 

 

This function enables you to retouch the shape of the lens.

   

   

Select 

.

   

   

   

   

The selection area is defined by two cursors 

 and 

. 

   

   

 

 

   

   

The area not affected by the modification is displayed in grey.

   

   

 

 

 

 

   

   

Drag the cursors 

 and 

 to delimit the selection area.

   

   

 

 

   

   
   

   

   

   

 

 

 

 

   

   

Select the type of retouch.

   

   

 

 

   

   

The types of retouch available vary according to the size of the selected area. 

   

   

 

 

   

   

•

 Retouch to create a straight line

•

 Retouch to create a curve

•

 Retouch to create an angle

   

   
   

   

The selected area is retouched. 

   

   

 

 

>

>

>

1

2

3

U

SER

 M

ANUAL

> V. M

ODIFYING

 

THE

 

LENS

 

SHAPE

79

Delta - Edging System > V1- 02-2020

Summary of Contents for DELTA




























































































































































































Reviews:

No comments