This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmental safe recycling.
BH-1701T
230-240 V~ 50 Hz
2000 W
IP24
To ensure your appliance gives you lasting service, you should clean it regularly.
Warning! To avoid the danger of anelectric shock or burning:
- always be sure that the appliance is switched OFF before cleaning or
attempting to store the item;
- allow the appliance to cool down;
- never immerse the appliance in water;
- never allow water or cleaning agent to run into the appliance.
1. Clear the external surface of the product by wiping it with a soft, damp cloth.
Caution! Never use caustic or abrasive cleaning agents,as this could damage
your appliance.
2. Always ensure the product’s housing is intact and completely assembled
before use.
When the product is plugged and push the ON/OFF (0/I) button located at the back of the
appliance,the buzzer “beeps” and the screen flashes for 3s, then in the standby mode. Push
again, if you want to switch off.
In standby mode,you can set the day and time.
SET THE CURREN DAY
Press
SET
, the day icon
（
1 2 3 4 5 6 7
）
flashes. Use + and - to set current day. Then press
OK
,
it will save and enter into next step automatically for hour setting
.
SET THE CURREN HOUR
The hour icon 01:00 flashes. Use + and - to set hour. Then press
OK
, the minute icon
00:01flashes. Use + and - to set minutes. In the end, press
OK
to confirm and save automatically.
Manual mode:
Press , start at 2000W (show on screen), you can do the following:
1) SET TEMPERATURE
Press
SET
, setting temperature flashes 20 (default temperature setting is 20°C), use + and - to
set and press
OK
to confirm(selected temperature range 5°C - 40°C).
2) CHANGE POWER
In Manual mode, press to set the power in following order: 2000W( )-1000W( )
-Fan ( ). Press again, the power changing will repeat the cycle.
Window mode(ONLY work during manual program):
Press to turn on open-window detection:
During open-window detection mode,once the ambient temperature drops 5-10
℃
within 10
minutes, then the product will stop working within 30 minutes and enter into stand by mode.
Press the button again to turn off open-window detection.
WEEKLY PROGRAM SETTING (PROGRAM MODE)
Weekly program explain:
1. It can set day by day from Monday to Sunday. And for each day, it can set 2 working periods
(P1/ P2).
2. The product works at full power (2000W) during weekly program.
Remark:
During the process of WEEKLY program setting, if you want to quick finish the setting, press
for 3 seconds to confirm and exit.
After complete all settings(14 working periods=7daysx2periods/day), if you want to
remove 1 period: go to this period, then press , the time will change to “OFF”.
For the current day: Before P1 starts, P1 working period will on the screen; If P1 pass, P2
working period will on the screen; If P2 pass, the timer symbol will show on the screen.
1.
2.
3.
WEEKLY PROGRAM SETTING:
In STANDY MODE: Press for 3 seconds, it enters into WEEKLY PROGRAM setting,the icon
lashes on the screen until complete the whole setting. And the day icon (1 2 3 4 5 6 7) flashes,
use + and - to select the day, P1 shows in screen (The wake up time for the initial setting, the
time shows “OFF”. Press , the time become and can start to set). Press
OK
, it enters
into next step - wake up time setting: the hour flash (use + and - to set(23-hours). Then press
OK
, it enters into next step - minutes setting: the minute icon flashes. Use + and – to
set minute(0-58 minutes). Then press
OK
, it enters into next step - temperature setting: setting
temperature flashes 20 (default temperature setting is 20°C), use + and - to set(selected
temperature range 5°C - 40°C). Press
OK
, it enters into next step - OFF time setting:
the hour flash use + and - to set(23-hours). Then press
OK
, it enters into next step - minutes
setting: to minute setting, the minute icon flashes. Use + and – to set minute (0-59
minutes). Press
OK
to confirm and it automatically enter to next working period. In this cycle,
you can set 7 days on/off timer.
The will be displayed on the working status. If you want to turn off the weekly program,
press to turn off,and the screen will disappear.
FR
ES
PT
IT
EL
PL
RU
UA
RO
EN
FR
ES
PT
IT
EL
PL
RU
UA
RO
EN
51
52
3. CLEANING
4. RECYCLING
