manualshive.com logo in svg

Epson U675 - TM Color Dot-matrix Printer, Service Manual

Share
Download
Epson U675 - TM Color Dot-matrix Printer Service Manual Download Page 217

Rev.D

Product Overview   Appendix D-29

TM-U675/U675P (with autocutter) Service Manual

Confidential

When the slip paper is fed forward, the respective gears rotate in the directions indicated by 
arrow a, arrow b, arrow c, arrow d, arrow e, and arrow f.  This rotates the slip feed roller and slip 
hold roller in the directions indicated by arrows g and h, feeding the slip paper in the direction 
indicated by the arrow.  When the slip paper is fed in the reverse direction, the operation is 
performed in the opposite direction. (See Figure D-37.)

Validation Mechanism

Feeding validation paper

When you use validation paper, the force of the drive of the paper feed motor  switches to the 
slip paper feed gear using the J/S change mechanism.

The open/close operation (see "Platen open and close operation") moves the platen lever frame 
in the direction of arrow a and the slip paper roller and platen are opened.  Validation paper can 
be inserted from the top of the printer mechanism in this state.  When the trailing edge of 
validation paper is detected, the detection signal is output.  This signal is received, the lever 
drive motor is started, and the platen lever moves in the direction of arrow b (in Figure D-8).  
This causes the slip feed roller and the slip hold roller to grasp the validation paper.  The platen 
closes to ensure the appropriate platen gap, and printing is possible.  When the printing of one 
line of characters is completed, the paper feed motor is driven to rotate the slip feed roller to feed 
the validation paper the prescribed amount in the upward direction.

Ribbon Feed Mechanism

The ribbon feed mechanism is comprised of the following parts. (See Figure D-38.)

❏

Transmission gear

❏

Ribbon reduction gear

❏

Ribbon drive gear

❏

Ribbon intermediate gear

❏

Ribbon take-up gear

❏

Ribbon take-up shaft

The rotation of the carriage transmission pulley driven via the carriage transmission belt is used 
to feed the ribbon. 

Summary of Contents for U675 - TM Color Dot-matrix Printer






































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands