manualshive.com logo in svg

Epson U675 - TM Color Dot-matrix Printer, Service Manual

Share
Download
Epson U675 - TM Color Dot-matrix Printer Service Manual Download Page 147

Rev.D

Assembly and Disassembly   2-113

TM-U675/U675P (with autocutter) Service Manual

Confidential

34. Attach the corresponding cover plate sub assemblies to the left and right sides of the cover 

frame sub assembly (two screws).

35. Insert the coil unit of the right and left hook springs onto the shafts of the cover frame sub 

assembly and hang the hooks on the slits in the cover frame sub assembly.  Hang the other 
ends of the right and left hook springs on the grooves of the right and left hook buttons and 
attach the right and left hook buttons to the shafts with two E-rings.

Figure 2-114  

102 Screw (C.B.S-tite F, 3X4)

groove

shaft

slit

102 Screw (C.B.S-tite F, 3X4)

175 Cover frame sub assembly

177 Left cover plate sub assembly

176 Right cover plate sub assembly

173 
Left hook spring

172 Right hook spring

170 Right hook button

163 E-ring (3)

163 E-ring (3)

169 Left hook button

shaft

hook

Summary of Contents for U675 - TM Color Dot-matrix Printer






































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands