manualshive.com logo in svg

Epson U675 - TM Color Dot-matrix Printer, Service Manual

Share
Download
Epson U675 - TM Color Dot-matrix Printer Service Manual Download Page 21

Rev.D

Troubleshooting   1-9

TM-U675/U675P (with autocutter) Service Manual

Confidential

Troubleshooting Using the ERROR LED 

You can learn the cause of a failure by checking the ERROR LED code.   The following table 
shows problems and solutions to repair the printer.  Numbers in the "Solutions" column indicate 
the order to use to check the problem.  If you cannot determine the cause of the problem after 
checking all the solutions listed, go back to the flowchart given earlier in this chapter.

Table1-2 Error causes and solutions

Type of Error and ERROR LED Pattern

Explanation

Solutions 
(Listed in the order you should use to check printer)

Autocutter Error

An autocutter error 
was detected.

1. Check for paper jams around the autocutter.  (See 

page 1-19.)

2. Check the cutter motor assembly. (See page 1-11.)  
    If there has been a short in the cutter motor 

assembly, replace the main circuit board unit at 
the same time.  (See page 2-96.)

3. Replace the main circuit board unit and see if the 

problem is fixed. (See page 2-96.)  

    If the printer is repaired, refer to Test Points on the 

Main Circuit Board Unit (See page 1-12.) to analyze 
the defective areas on the board.

Carriage home position detection 
error

The head carriage 
home position was 
not correctly 
detected.

1. Check the carriage assembly for a paper jam. 

(To remove the carriage cover, see page 1-16.)

2. Check for paper dust on the H.P. detector 

assembly.  (To remove the carriage cover, see 
page 1-16.)

3. Replace the H.P. detector assembly. (See page 2-

22.)

Carriage out-of-step error

There is no carriage 
detector output 
even when the 
carriage is 
instructed to move.

1. Check the carriage assembly for a paper jam. 

 (To remove the carriage cover, see page 1-16.)

2. Check the rotary encoder on the carriage motor 

gear used to detect carriage position (The rotary 
encoder is on the intermediate circuit board 
assembly. You need to disassemble the 
intermediate circuit board assembly to check the 
encoder. To remove the intermediate circuit 
board assembly, see page 2-22.)

3. Check the carriage motor.  (See page 1-11.) 

If the motor is shorted, replace it along with the 
main board.

4. Replace the main circuit board unit and see if the 

problem is fixed. (See page 2-96)  

Slip eject error

The slip paper was 
not ejected 
normally.

1. Look into the printer from the left side to check for 

a paper jam in the slip paper transport path.

2. Check the paper feed motor.  (See page 1-11)

If the motor is shorted, replace it along with the 
main board.

3. Try installing a new main circuit board unit to see if 

the printer is fixed.    (See page 2-96)

320ms

5120ms

LED ON

Summary of Contents for U675 - TM Color Dot-matrix Printer






































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands