manualshive.com logo in svg

Epson U675 - TM Color Dot-matrix Printer, Service Manual, Page: 199 / 325

Share
Download
Epson U675 - TM Color Dot-matrix Printer Service Manual Download Page 199

Rev.D

Product Overview   Appendix D-11

TM-U675/U675P (with autocutter) Service Manual

Confidential

Roll paper end detector mechanism

The roll paper end detector mechanism detects the presence of roll paper.  It is located behind 
the sub paper feed roller in the roll paper feed path so that it can detect the insertion of paper 
when semi-automatically loading roll paper.  

The roll paper end detector includes an LED and a phototransistor.  The reflection of light is 
used to detect the presence of paper.  

When there is paper in the feed path, or when you are performing semi-autoloading, LED light 
is reflected when the roll paper is inserted.  This changes the output level of the phototransistor.  
The change in output level is detected and is used as the detection signal for the presence of roll 
paper. 

Figure D-16  

GND

High

+5V

GND

Low

When light is

 interrupted 

When light is emitted

Printer side

Roll paper

Signal level at point A

Summary of Contents for U675 - TM Color Dot-matrix Printer






































































































































































































































































































































Reviews:

No comments