manualshive.com logo in svg

Epson U675 - TM Color Dot-matrix Printer, Service Manual, Page: 209 / 325

Share
Download
Epson U675 - TM Color Dot-matrix Printer Service Manual Download Page 209

Rev.D

Product Overview   Appendix D-21

TM-U675/U675P (with autocutter) Service Manual

Confidential

Clamshell mechanism

The clamshell mechanism consists of a paper feed unit, paper feed frame shaft, and paper feed 
frame fixing lever.  This mechanism is used in the event of a quality problem, such as a paper 
jam.

Figure D-30  

❏

Opening mechanism

1. Press the 

➝

 on the two paper feed frame fixing levers (indicated by "arrow a" in Figure 

D-30).

2. The paper feed frame fixing lever comes off the main frame, allowing the entire paper 

feed unit to rotate on the paper feed frame shaft. (See Figure D-31.)

3. Rotate the entire paper feed unit approximately 90

°

 in the direction indicated by arrow 

b. (See Figure D-31.)

Paper feed unit

Paper feed frame fixing levers

Paper feed frame shaft

Main frame

Summary of Contents for U675 - TM Color Dot-matrix Printer






































































































































































































































































































































Reviews:

No comments