manualshive.com logo in svg

Epson U675 - TM Color Dot-matrix Printer, Service Manual

Share
Download
Epson U675 - TM Color Dot-matrix Printer Service Manual Download Page 202

Appendix D-14

   Product Overview

Rev.D

Confidential

Front cover open detection mechanism

The front cover open detector is located at the right side of the printer mechanism, and detects 
opening and closing of the front cover.  This detector consists of an LED and phototransistor.  A 
screening part, located on the rear of the cover, interrupts light rays when the cover is closed.  
When the cover is opened, the light rays reach the phototransistor, resulting in a change in its 
output level.  This change in output level is used as a detection signal to determine when the 
front cover is open.

Figure D-21  

Rear cover detector mechanism

The rear cover detector is located in the back, right side of the printer mechanism.  It detects 
whether the rear cover is open or closed.  This detector is comprised of an LED and 
phototransistor.  When the cover is closed, the light interrupter on the back of the cover 
interrupts the optical axis.  When the cover is open, the optical axis is opened, which changes the 
output level of the phototransistor.  The detector takes this output level as the detection signal 
for the rear cover open detector.

Figure D-22  

GND

High

+5V

GND

Low

Printer side

Front cover light interrupter unit

When light is

 interrupted

When light is emitted

Signal level at point A

GND

High

+5V

GND

Low

Printer side

Rear cover light interrupter unit

When light is

 interrupted

When light is emitted

Signal level at point A

Summary of Contents for U675 - TM Color Dot-matrix Printer






































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands