Epson TP3 Manual Download Page 30 | Manualshive

Page: 30 / 96

Epson TP3 Manual Download Page 30

Functions & Installation 6. Enable Switch

20

RC700-A option TP3 Rev.8

6. Enable Switch

In TEACH mode, some operations require use of the 3-position enable switch located on
the back of the Teach Pendant. The enable switch can be operated by either hand.

When operation of the enable switch is required, grip either switch to the center position
(ON state). If you grip the switch harder, it will be OFF state and the robot will stop.

Enable Switch (for Left Hand)

Back view

Left side

Right side

Enable Switch (for Right Hand)

How to press the Enable switch

Grip the enable switch by fingers of the hand holding the handler.

Example

: When gripping by the left hand

Handle

Make sure to grip to the center position (ON state) when enabling the enable switch. If
the enable switch is not pressed enough to the center position (ON state), an error will
occur and the robot will stop due to the enable switch being in the OFF state.
Also, the following error message will appear when an error is occurred.

Restart (supply the power source of the Controller again) of the teaching pendant is
required to recover from the error.



NOTE

«
...
28
29
30
31
32
...
»

Summary of Contents for TP3

































































































Reviews:

No comments